Test & Measurement


Current analyser for low-power devices

9 November 2016 Test & Measurement

Keysight Technologies introduced the world’s first analyser enabling a minimum of 100 pA level dynamic current measurements with a maximum of 200 MHz bandwidth, 1 GSps sampling rate and 14- or 16-bit wide dynamic range.

The CX3300 Series device current waveform analyser is a new category of instrument and is ideally suited for researchers struggling with high-speed transient current measurements during advanced device characterisation and engineers working to reduce power/current consumption in low-power devices.

Characterising advanced devices and evaluating low-power devices are challenging tasks; ones that require engineers to measure high-speed (over 1 MHz) and low-level dynamic current (below 1 A). However, the existing methodology for this measurement is plagued by many issues – a large noise, voltage drop, limited dynamic range, bandwidth – and as a result, low-level dynamic current often goes undetected and unmeasured.

Keysight’s new analyser overcomes this limitation by enabling the simultaneous measurement of wideband and low-level current waveforms. By providing a 14-bit or 16-bit wide dynamic measurement range, the system can meet a wide range of measurement requirements without using multiple instruments. A graphical user interface on a WXGA 14,1” multi-touch display, and advanced measurement and analysis software, make previously difficult low-level current waveform measurements and analyses more efficient and easier to make.

Using the CX3300, researchers can now measure transient current even if the pulse width is very narrow (less than 100 ns). This capability is particularly beneficial for device engineers developing semiconductor or advanced memory devices, since it allows them to visualise previously unmeasurable waveforms. Current consumption waveforms can also be clearly captured at any point in time, whether the device is in its sleep/standby or active state. By being able to clearly see how a device consumes power, engineers are better able to quantitatively evaluate and reduce a device’s power /current consumption.

In addition to measuring dynamic current, the analyser can also be used as a debugging tool, enabling deep-dive and accurate evaluation during R&D. Engineers are able to write more aggressive power consumption specifications, and in turn, realise more confident power reduction.

The analyser consists of a mainframe with a touch display and current sensors specifically dedicated to precision current waveform measurements. The mainframe features a 14-bit or 16-bit wide dynamic range, 200 MHz maximum bandwidth, and a fast sampling rate of 1 GSps. The low-noise and wideband current sensors support dynamic current measurements from 10 A down to 100 pA level.

For more information contact Lizzy Mabaso, Concilium Technologies, +27 (0)12 678 9200, [email protected], www.concilium.co.za



Credit(s)



Share this article:
Share via emailShare via LinkedInPrint this page

Further reading:

High-speed AWG generates up to 20 sine waves
Vepac Electronics Test & Measurement
Spectrum Instrumentation has released a new firmware option for its range of versatile 16-bit Arbitrary Waveform Generators, with sampling rates up to 1,25 GS/s and bandwidths up to 400 MHz.

Read more...
E-mobility: Navigate safety, interoperability and conformance
Concilium Technologies News
In this whitepaper, these challenges are discussed in more detail and the question is asked: How can EV and EVSE manufacturers navigate a complex regulatory landscape and deliver a quality product, without compromising time-to-market projections?

Read more...
Digitisers upgraded with pulse generator option
Vepac Electronics Test & Measurement
Spectrum Instrumentation has added the Digital Pulse Generator option to its ultrafast digitisers (with up to 10 GS/s speed) and arbitrary waveform generators.

Read more...
Network Master Pro to provide support of OpenZR+
Tamashi Technology Investments Test & Measurement
Anritsu Corporation has introduced the 400G (QSFP-DD) multi-rate module MU104014B that supports the new interface standard.

Read more...
Upgrade brings extra layer of detection to Fluke’s acoustic imagers
Comtest Test & Measurement
The firmware 5.0 update helps to boost efficiency and allows maintenance technicians to scan large areas quickly, and visually pinpoint technical issues before they become critical.

Read more...
Companies collaborate on EnviroMeter
Avnet Silica Test & Measurement
STMicroelectronics and Mobile Physics have joined forces to create EnviroMeter for accurate air-quality monitoring on smartphones. Time-of-flight optical sensing enables an accurate personal air quality monitor and smoke detector.

Read more...
PCB test points
Vepac Electronics Test & Measurement
Maintaining these access points in the final production versions will prove invaluable during the life of the equipment for service, adjustment, and debug, or repair activities.

Read more...
RFID reader
Test & Measurement
The EXA81 from Brady turns any smartphone or tablet into a personal radar that can pick up radio signals from all RFID-labelled items.

Read more...
Proximity sensor with VCSEL
Avnet Abacus Test & Measurement
Vishay’s newest small package proximity sensor, the VCNL36828P, combines low idle current with an I2C interface and smart dual slave addressing.

Read more...
CNH data output devices for AI applications
Altron Arrow Test & Measurement
STMicroelectronics’ CH family of time-of-flight sensor devices feature compact and normalised histogram (CNH) data output for artificial intelligence applications requiring raw data from a high-performance multizone ToF sensor.

Read more...