Analogue, Mixed Signal, LSI


Isolated current transducers

19 July 2017 Analogue, Mixed Signal, LSI

LEM expanded its miniature, integrated circuit transducers range for AC and DC isolated current measurement up to 300 kHz with the introduction of the GO series. These new components offer full isolation despite their small size, by integrating the primary conductor for nominal current measurements of 4 A, 6 A, 8 A, 10 A, 12 A, 16 A, 20 A or 30 A with a measurement span of 2,5 times the nominal current . Products in the GO series are able to support high overload currents up to 200 A peak for short durations (1 ms).

The transducers are mounted directly onto a printed circuit board as SO8 or SO16 SMD devices. They are simple to use as they integrate low resistance primary conductors (minimising power losses) within a proprietary ASIC to allow direct current measurement and consistent insulation performance, while still providing high creepage and clearance distances.

Standard models provide an analog voltage output with different sensitivity levels according to the models to achieve an output voltage of 800 mV @ IPN for 5 V versions and 500 mV @ IPN for 3.3 V versions. Ratiometric output is also an option through dedicated models.

For more information contact Denver Technical Products, +27 (0)11 626 2023, denvertech@pixie.co.za, www.denver-tech.co.za



Credit(s)



Share this article:
Share via emailShare via LinkedInPrint this page

Further reading:

High-speed PIN diode
Altron Arrow Analogue, Mixed Signal, LSI
Vishay’s new high-speed Silicon PIN diode is able to detect both visible and near infra-red radiation over a wide spectrum range from 350 to 1100 nm.

Read more...
Analogue front end for sensor measurements
Electrocomp Analogue, Mixed Signal, LSI
The NJU9103 AFE from Nisshinbo is a tiny analogue front end, with a 16-bit resolution ADC and up to 512 x signal amplification from the programmable gain amplifier.

Read more...
Single-channel software configurable I/O
Altron Arrow Analogue, Mixed Signal, LSI
These use cases of the AD74115H include analogue output and input, digital output and input, resistance temperature detector (RTD), and thermocouple measurement capability.

Read more...
Current-sense amplifier with PWM rejection
Altron Arrow Analogue, Mixed Signal, LSI
Analog Devices’ AD8410A is a high voltage, high bandwidth current-sense amplifier that features an initial gain of 20 V/V and a 2,2 MHz bandwidth.

Read more...
Combining a LPF and ADC driver for a 20 Vp-p signal
Altron Arrow Analogue, Mixed Signal, LSI
A mixed-signal ADC driver circuit’s optimum performance depends on multiple variables: the driver’s settling time, the RC filter’s time constant, driving impedance, and the ADC sampling capacitor’s kickback current, all interact during acquisition time and contribute towards sampling errors.

Read more...
Pressure sensor with NextNav certification
EBV Electrolink Analogue, Mixed Signal, LSI
STMicroelectronics’ LPS22DF pressure sensor has received a NextNav certification, which guarantees performance and reliability for geolocation and other types of applications.

Read more...
Reference design for Raspberry Pi analogue I/O
Analogue, Mixed Signal, LSI
Analogue Devices has published a reference design for ±10 V analogue input and ±15 V analogue output for Raspberry Pi platforms.

Read more...
Multi-zone distance sensor with 90° field of view
Avnet Silica Analogue, Mixed Signal, LSI
STMicroelectronics has revealed a new FlightSense multi-zone distance sensor, with 90° field of view, to bring lifelike situational awareness to applications like home automation, computers, robots, and smart equipment.

Read more...
Six-axis IMU with Qvar sensing channel
Altron Arrow Analogue, Mixed Signal, LSI
The LSM6DSV16X from STMicroelectronics is a high-performance, low-power six-axis IMU, featuring a three-axis digital accelerometer and a three-axis digital gyroscope.

Read more...
Bidirectional current-sense amplifier with PWM
RS South Africa Analogue, Mixed Signal, LSI
The MAX49925 from Analogue Devices is a bidirectional current-sense amplifier (CSA) with an input common-mode range that extends from -40 to 76 V, making it suitable for 48 V HEV applications where there are large automotive transients.

Read more...