Switches, Relays & Keypads


Rotary sensor with SSI output

28 April 2021 Switches, Relays & Keypads

New from Bourns is the Model DMS22B non-contacting feedback rotary sensor that features Synchronous Serial Interface (SSI) output providing effective synchronisation in closed-loop control systems. This single-turn rotary sensor is based on Hall-effect technology and is supported by a factory programmable electrical angle from 10 to 360 degrees that enables more consistent and dependable operation of up to 50 million shaft revolutions.

The sensor is designed with non-contacting magnetic technology offering consistent performance and high reliability that is well suited for a range of application environments.Plus, its IP50 seal rating makes this rotary sensor highly resistant to fluid/dust ingress.

Available with a 7/8-inch flatted shaft and bushing mount configuration, the DMS22B offers designers a highly versatile position sensing solution for a broad variety of applications including patient platform positioning feedback, pneumatic control valve position feedback, draw wire position sensors, remote communications antenna positioning, actuator motor position feedback, automated manufacturing robotics and more.

For more information contact Electrocomp, +27 11 458 9000, sales@electrocomp.co.za, www.electrocomp.co.za


Credit(s)



Share this article:
Share via emailShare via LinkedInPrint this page

Further reading:

Temperature and humidity sensors for cold chains
26 May 2021, Electrocomp , Analogue, Mixed Signal, LSI
New calibrated and ISO 17025-certified temperature, and humidity and temperature sensors have been announced by Sensirion.These sensors enable customers to achieve cost-efficient GDP (good distribution ...

Read more...
Rotary sensor with SSI output
26 May 2021, Electrocomp , Switches, Relays & Keypads
New from Bourns is the Model DMS22B non-contacting feedback rotary sensor that features Synchronous Serial Interface (SSI) output providing effective synchronisation in closed-loop control systems. This ...

Read more...
Current-compensated ring core chokes
26 May 2021, Electrocomp , Circuit & System Protection
TDK has released a new series of current-compensated EPCOS double-ring core chokes for the suppression of common-mode interference. They are available in three sizes with current handling capacities between ...

Read more...
Reference design for humidity and temperature sensors
26 May 2021, Electrocomp , Design Automation
The SHT4x Smart Gadget is a simple reference design circuit board which demonstrates the performance and ease of use of Sensirion’s SHT4x humidity and temperature sensors. It is equipped with a liquid ...

Read more...
Watertight glass reinforced polyester enclosures
28 April 2021, Electrocomp , Enclosures, Racks, Cabinets & Panel Products
Glass reinforced polyester (GRP) enclosures from Hammond Manufacturing are lightweight and corrosion resistant. They are also UV-resistant, enabling them to be installed inside and outside. The new ...

Read more...
Common-mode choke for automotive CAN-FD
28 April 2021, Electrocomp , Passive Components
TDK unveiled its new ACT1210D Series common-mode choke for automotive CAN-FD, which began mass production in April 2021. Automotive LANs (local area networks) are roughly categorised into four systems: ...

Read more...
Dual-band GNSS RTK module
28 April 2021, Electrocomp , Telecoms, Datacoms, Wireless, IoT
The RTK-1010 is a high-performance dual-band GNSS RTK module that is designed for applications requiring centimetre-level positioning accuracy. It adopts a 12 nm manufacturing process and integrates an ...

Read more...
Small E-Stop button with 360° visibility
28 April 2021, RS Components (SA) , Switches, Relays & Keypads
RS Components has added the Eaton RMQ Small E-Stop to its emergency pushbutton portfolio. This compact device is around 30% smaller than standard emergency-stop buttons and is designed to deliver improved ...

Read more...
Digital flow sensor for respiratory devices
31 March 2021, Electrocomp , Test & Measurement
The compact SFM3119 digital flow meter is the successor to Sensirion’s SFM3100 mass flow meter. Compared to its predecessor, the SFM3119 comes with a digital I2C output as well as improved specifications. The ...

Read more...
Upcoming modifications to Bourns’ isolation power transformers
26 February 2021, Electrocomp , Passive Components
In the spirit of continuous improvement, effective 14 June 2021, Bourns is changing the silicone material, Hi-pot specification and marking content for its HCT Series high clearance/creepage distance ...

Read more...