News


Research out of Finland explores more eco-friendly electronics

24 November 2021 News

The amount of electronics will inevitably continue to increase and the use of raw materials in the sector is expected to double by 2050. The amount of electronic waste has also almost doubled over the past 16 years and only 20% of this waste is collected efficiently. The EU has therefore called for more sustainable solutions from the electronics industry and VTT (Technical Research Centre of Finland) is developing them by combining printed electronics, bio-based materials and ecodesign thinking.

The environmental load of the electronics industry can be significantly reduced by moving from traditional manufacturing processes to printed electronics and from fossil-based materials to bio-based materials. By using printing processes, up to 90% of fossil materials can be replaced in some applications. At the same time, energy consumption may decrease to one fifth compared to traditional processes. Ecodesign, on the other hand, promotes the efficient use, recycling and recovery of valuable materials.

VTT has versatile expertise in all these areas and can provide extensive knowledge in both electronics manufacturing and new environmentally-friendly materials. In the ECOtronics project funded by Business Finland, this expertise has been combined to assess the environmental load of electronics and to develop sustainable solutions and determine their feasibility.

“The environmental impact of electronics is caused by, among other things, the used raw materials and manufacturing processes and the use, recycling and post-treatment of products. The environmental load must be examined on a case-by-case basis throughout the life cycle of the product so that the right route to reduce it may be found,” says Liisa Hakola, the leader of the ECOtronics project at VTT.

Solutions tested in demo cases

VTT and university partners have tested the feasibility of new sustainable solutions through demo cases. The subject of one demo was a smart label printed on bio-based plastic, which is powered by a supercapacitor rechargeable with solar panels, even indoors. The label can be added as a part of the product packaging and can be used to monitor, for example, the transport conditions of food and medicines or other heat-sensitive products. The solution is also suitable for monitoring different spaces and among other things, for monitoring moisture, pressure or damage sustained by products. Another demo case concerned a biodegradable antenna connected to a circuit board, which is suitable in wireless transfer of measurement data, for example.

One of the advantages of bio-based materials is that their properties can be modified in many ways. This enables completely new applications. “For example, a smart label is light, thin and flexible. It is suitable for, among other things, wearable electronics for which traditional heavy, thick and rigid circuit boards are not suitable. We will continue to explore these opportunities,” says Maria Smolander, research team leader at VTT.

Sustainable electronics for business needs

VTT helps companies in the electronics industry find new solutions for sustainable electronics. Eight companies interested in sustainable electronics participated in the ECOtronics project. For example, the package industry operator Iscent received help in material selection and testing and the health technology developer GE Healthcare in ecodesign and environmental impact assessment.

“We wanted to explore and test new bio-based materials and we found new alternatives, one of which was perfectly suited to our customer. This helped us to sign a significant contract,” says Raimo Korhonen, partner and project manager, Iscent Oy.

GE Healthcare wanted to investigate the environmental impact of its new pulse oximeter, which is a cordless device placed on a patient's finger. “We compared the environmental load of our product concept with the alternatives available on the market and examined possible benefits and problem areas in terms of environmental impact. The significance of the environmental load was also assessed by comparing it with examples from everyday life, such as one litre of milk. In this comparison, the product concept's performance was excellent,” says Juha Virtanen, hardware project leader, GE Healthcare.

In addition to Iscent and GE Healthcare, the Finnish companies New Cable Corporation, Paptic, Green Company Effect, Stora Enso, Vaisala and Confidex participated in the ECOtronics project. VTT's research partners are Tampere University, LUT University and LAB University of Applied Sciences.

More information about the ECOtronics project can be found at www.ecotronics.fi




Share this article:
Share via emailShare via LinkedInPrint this page

Further reading:

From the editor's desk: AI – a double-edged sword
Technews Publishing News
As with any powerful tool, AI presents challenges, some of which, if not carefully managed, threaten to undo the potential that it can offer.

Read more...
Global semiconductor sales increase
News
The Semiconductor Industry Association (SIA) has announced global semiconductor sales were $57,0 billion during the month of April 2025, an increase of 2,5% compared to the March 2025.

Read more...
Avnet Abacus announced new president
Avnet Abacus News
Avnet Abacus has announced that Mario Merino will succeed Rudy Van Parijs as president of Avnet Abacus, effective 1 July 2025.

Read more...
Avnet Abacus wins multiple prestigious awards
Avnet Abacus News
The awards from Molex recognise outstanding performance, collaboration, and significant growth in the challenging market conditions of 2024.

Read more...
Components distribution slowdown Q1 2025
News
European components distribution (DMASS) experienced a continued slowdown in the first quarter 2025.

Read more...
Semiconductor sales increase 17% YoY
News
The Semiconductor Industry Association (SIA) recently announced global semiconductor sales were $54,9 billion during the month of February 2025, an increase of 17,1% compared to the February 2024 total.

Read more...
Silicon Labs – Q1 results
News
Silicon Labs, a leading innovator in low-power wireless, recently reported financial results for the first quarter, which ended April 5, 2025.

Read more...
Strengthening industry through strategic partnerships at KITE 2025
Specialised Exhibitions News
The KwaZulu-Natal Industrial Technology Exhibition is not just an exhibition, it is a powerhouse of industry collaboration where visitors and exhibitors gain access to authoritative insights, technical expertise, and high-impact networking opportunities.

Read more...
Solar Youth Project calls on industry to step up
News
With the second cohort completed training and the first cohort returning for their final module, host companies are urgently needed to turn the training into a long-term opportunity.

Read more...
Conlog powers SA’s future with national smart meter rollout
News
Conlog recently secured the RT29-2024 contract from National Treasury, which is seen to be a major milestone towards modernising SA’s utility infrastructure.

Read more...









While every effort has been made to ensure the accuracy of the information contained herein, the publisher and its agents cannot be held responsible for any errors contained, or any loss incurred as a result. Articles published do not necessarily reflect the views of the publishers. The editor reserves the right to alter or cut copy. Articles submitted are deemed to have been cleared for publication. Advertisements and company contact details are published as provided by the advertiser. Technews Publishing (Pty) Ltd cannot be held responsible for the accuracy or veracity of supplied material.




© Technews Publishing (Pty) Ltd | All Rights Reserved