Targeting high-volume applications, the SPD800 series of CMOS technology digital and analog differential pressure sensors from Sensirion have been designed to measure the pressure of air and non-aggressive gases and deliver accurate and stable results covering a range of up to ±500 Pa (±5 millibars or ±5 cm of water), even at very low differential pressures.
The products are based on Sensirion’s CMOSens technology, which integrates a sensor element and all the necessary signal conditioning electronics – including analog and digital signal processing – on a single tiny CMOS chip. The technology is well proven and is suited for high-quality and cost-sensitive volume production.
The SDP800 series sensor element, which uses flow-through technology to measure differential pressure, together with the on-chip signal processing and digital calibration, delivers high accuracy with no offset drift, right down to the lower end of the measurement range. These new CMOSens-based sensors largely overcome the limitations in offset drift and accuracy of traditional static or dynamic differential pressure sensors commonly used in HVAC applications.
Available in the SDP800 series are the 4-pin, ±500 Pa SDP800-500PA and the 4-pin, ±125 Pa SDP800-125PA. As well as offering characteristics including high reliability, long-term stability and an excellent signal-to-noise ratio, the sensors also feature a two-wire digital interface for easy connection to microcontrollers. In addition, the Sensirion EK-P5 evaluation kit enables easy and fast sensor evaluation via PC test software, connected via USB cable.
High-performance IMU RS South Africa
Analogue, Mixed Signal, LSI
TDK Corporation has announced availability of the new InvenSense SmartMotion ICM-536xx family of high-performance 6-axis IMUs.
Read more...Wide frequency range inductors RS South Africa
Passive Components
TDK Corporation has expanded its ADL4524VL series (4,5 x 2,4 x 2,6 mm – L x W x H) of wire-wound inductors for automotive power-over-coax.
Read more...High-temperature closed-loop MEMS accelerometer RS South Africa
Analogue, Mixed Signal, LSI
This sensor from TDK is a high-temperature MEMS accelerometer with ±14 g input range and a digital interface for measurement while drilling applications.
Read more...Dual accelerometers on the same die Altron Arrow
Analogue, Mixed Signal, LSI
The LSM6DSV320X is the first mainstream inertial sensor to house a gyroscope alongside two accelerometers, one capable of sensing up to ±16 g and one sensing up to a staggering ±320 g.
Read more...Dual-range IMU with edge processing EBV Electrolink
Analogue, Mixed Signal, LSI
ST’s innovative LSM6DSV80X combines two accelerometer structures for 16 g and 80 g full-scale sensing, a gyroscope up 4000 dps, and embedded intelligence in a single component.
Read more...Automotive power-over-coax inductor RS South Africa
Power Electronics / Power Management
TDK has launched the ADL8030VA, a high-performance inductor designed specifically for power-over-coaxial applications.
Read more...3-terminal filters for automotive applications RS South Africa
Power Electronics / Power Management
TDK has expanded its YFF series of 3-terminal filters for automotive applications to include higher voltages up to 35 V and higher capacitances up to 4,7 µF.
Read more...High-reliability isolation amplifiers EBV Electrolink
Analogue, Mixed Signal, LSI
The VIA series of isolation amplifiers from Vishay are designed to deliver exceptional thermal stability and precise measurement capabilities.
Read more...Mibbo QT2C Series signal isolators Conical Technologies
Analogue, Mixed Signal, LSI
The Mibbo QT2C Series isolators support a rich combination of input and output signals, working with either current loops or voltage levels.
Read more...IMU with dual-sensing capability EBV Electrolink
Analogue, Mixed Signal, LSI
ST’s 6-axis inertial measurement unit integrates a dual accelerometer up to 320g and embedded AI for activity tracking and high-impact sensing.
While every effort has been made to ensure the accuracy of the information contained herein, the publisher and its agents cannot be held responsible for any errors contained, or any loss incurred as a result. Articles published do not necessarily reflect the views of the publishers. The editor reserves the right to alter or cut copy. Articles submitted are deemed to have been cleared for publication. Advertisements and company contact details are published as provided by the advertiser. Technews Publishing (Pty) Ltd cannot be held responsible for the accuracy or veracity of supplied material.
printer friendly version