Power Electronics / Power Management


Battery optimisation software for IoT devices

27 February 2019 Power Electronics / Power Management Test & Measurement

Keysight Technologies has introduced the X8712A IoT device battery life optimisation software solution, to ensure optimal battery life prior to device deployment to accelerate troubleshooting and device verification.

Many IoT devices today run on battery power. For mission-critical IoT applications such as those in the healthcare and industrial industries, where lives can be at risk due to premature device failure, battery life is more crucial than ever. The challenge falls to IoT device makers to ensure the battery life of their devices will live up to expectations in the real world.

Keysight’s new X8712A solution enables IoT device makers to perform event-based power consumption analysis on IoT devices to gain a better understanding of how they spend their battery charge when operating in real-world conditions.

Design weaknesses can be detected with a wide dynamic-range current measurement and fast 20 µs sampling rate to capture an IoT device’s dynamic current consumption for a specific radio frequency or direct current event. It then automatically correlates that event to the device’s current consumption to easily identify the subsystems or events requiring optimisation.

Battery life can be optimised by calculating the RF or DC event’s occupancy time and current consumption contribution in percentage. By specifying the battery capacity and area of interest, the software estimates battery life based on the device’s charge consumption, so necessary steps can be taken to improve battery life.

For more information contact Tshiamo Mogakwe, Concilium Technologies, +27 12 678 9200, info@concilium.co.za, www.concilium.co.za



Credit(s)



Share this article:
Share via emailShare via LinkedInPrint this page

Further reading:

Wide-input DC/DC converters in 1/32nd bricks
Brabek Power Electronics / Power Management
RECOM now offers through-hole, 1/32nd brick-footprint, non-isolated DC/DC converters – the RPMA-4.5 and RPMA-8.0 – with 4,5 A and 8 A output ratings respectively. Each part has a wide 9-53 V input and ...

Read more...
USB charger solution with high power density
Altron Arrow Power Electronics / Power Management
Diodes Incorporated has launched a three-chip solution for enhancing the performance of ultra-high-power-density USB Type-C power delivery (PD) systems. These products can be used in a wide variety of ...

Read more...
Totem pole PFC controller
EBV Electrolink Power Electronics / Power Management
A new addition was made to ON Semiconductor’s solution set for ultra-high density offline power supplies in the form of the NCP1680, a dedicated critical conduction mode totem pole PFC controller. It ...

Read more...
Compact offline switcher ICs
EBV Electrolink Power Electronics / Power Management
Power Integrations introduced LinkSwitch-TNZ, a new switching power supply IC that combines offline power conversion, lossless zero-crossing detection and optionally, X-capacitor discharge functions in ...

Read more...
100 W and 300 W eighth-brick converters
Brabek Power Electronics / Power Management
Recom has introduced two new cost-effective DC/DC products with outputs of 100 W and 300 W in a DOSA-compatible, low-profile, through-hole eighth-brick format (58,4 x 23 mm). The RPA100E-W 100 W part ...

Read more...
High-side current sense amplifier with adjustable gain
NuVision Electronics Power Electronics / Power Management
The MPQ8112A is a low-cost, unipolar, high-side current sense amplifier that operates from a 2,7 V to 60 V supply and typically consumes a 300 μA current. The Monolithic Power Systems part is ideal for ...

Read more...
Super-junction 800 V MOSFETs
Altron Arrow Power Electronics / Power Management
The new super-junction STPOWER MDmesh K6 series from STMicroelectronics enhances several key parameters to minimise system-power losses. It is especially suited to lighting applications based on flyback ...

Read more...
DC/DC converter for forklift trucks
Vepac Electronics Power Electronics / Power Management
The DC/DC converters of the series PCMDS550-FT from MTM Power are tailor-made to meet the requirements in forklift truck technology. Highest quality and safety are of particular importance when using ...

Read more...
Wide-input buck converters in tiny package
Brabek Power Electronics / Power Management
RECOM now offers through-hole, 1/32nd brick footprint, non-isolated DC/DC converters by way of the RPMA-4.5 and RPMA-8.0, with 4,5&nbs;A and 8 A output ratings respectively. Each part has a wide 9-53 V input ...

Read more...
Air-insulated HV power supplies
Vepac Electronics Power Electronics / Power Management
XP Glassman’s OQ Series of high-voltage AC/DC power supplies are sophisticated 8 kW or 16 kW open-stack units with extremely low ripple and noise. The air-insulated, fast-response supplies exhibit tight ...

Read more...