Passive Components


Qi-compliant wireless charging coils

28 August 2019 Passive Components

Vishay has expanded its offering of Qi-compliant wireless charging transmitter and receiver coils with the introduction of 14 new products in industry-standard shield sizes.

Consisting of eight single-coil transmitters, three three-coil transmitters and three single-coil receivers, the products offer designers a source for the most popular sizes used in Qi wireless charging pads for handheld battery-powered devices. Available transmitter coil types include A11, A6, MP-A9, MP-A6, MP-A4 and MP-A2.

The transmitters offer power ratings from 5 W to 15 W, while receivers feature power ratings of 3,5 W and 5 W. The RoHS-compliant coils operate over temperatures from -40°C to +125°C and offer inductance tolerance of +10%. All configurations are customisable to customer specifications upon request.

For more information contact Quatraine Domoney, Avnet South Africa, +27 11 319 8600, quatraine.domoney@avnet.eu, www.avnet.co.za



Credit(s)



Share this article:
Share via emailShare via LinkedInPrint this page

Further reading:

MEMS-based environmental pressure sensors
25 March 2020, Avnet South Africa , Analogue, Mixed Signal, LSI
Bourns Sensors & Controls’ product line is introducing four new series of environmental sensors based on microelectromechanical systems (MEMS) technology. These four new series are designed for the customer ...

Read more...
Bluetooth 5.0 Low Energy module
25 March 2020, Avnet South Africa , Telecoms, Datacoms, Wireless, IoT
An output power of up to +8 dBm and the high sensitivity of the nRF52840, in combination with the LE coded PHY, make the module very attractive for applications that require a long range. The Bluetooth ...

Read more...
Complete design solution for energy efficient motor driving system
25 March 2020, Avnet South Africa , Power Electronics / Power Management
Electric motors are a powerhouse user of electricity worldwide, accounting for about two-thirds of industrial electricity consumption. The International Energy Agency reports that electric motors account ...

Read more...
Thick film resistors with wide terminals
26 February 2020, TRX Electronics , Passive Components
High reliability and enhanced terminal strength are essential in power designs. KOA’s wide-terminal resistors offer several advantages compared to standard footprints. The 0612 chip size allows a 6 times ...

Read more...
Miniature automotive MOSFETs
25 March 2020, Avnet South Africa , Power Electronics / Power Management
Diodes Incorporated announced the introduction of the 40 V-rated DMTH4008LFDFWQ and 60 V-rated DMTH6016LFDFWQ automotive-compliant MOSFETs packaged in DFN2020. These miniature MOSFETs occupy just 10% ...

Read more...
New PIC MCU family
25 March 2020, Avnet South Africa , DSP, Micros & Memory
In microcontroller (MCU)-based system design, software is often the bottleneck for both time to market and system performance. By offloading many software tasks to hardware, Microchip Technology’s new ...

Read more...
Modern flanged enclosures for IIoT and sensor applications
25 March 2020, Avnet South Africa , Enclosures, Racks, Cabinets & Panel Products
OKW Gehäusesysteme has expanded its range of enclosures with the new EASYTEC. The special feature of this enclosure range is that there are fully integrated lugs on the short end faces of the bottom part. ...

Read more...
Hybrid capacitors combine the best of both worlds
26 February 2020, Avnet South Africa , Power Electronics / Power Management
The different properties of EDLCs, Li-ion batteries and Li-ion capacitors suits each technology to various different applications.

Read more...
Innovative power capacitor technologies for wide band-gap semiconductors
26 February 2020, Electrocomp , Passive Components
Conventional semiconductors based on silicon are being replaced by wide band-gap (WBG) technologies based on GaN (gallium nitride) and SiC (silicon carbide). These demand a great deal from the passive ...

Read more...
Automotive-compliant power transformers
26 February 2020, Electrocomp , Passive Components
Bourns’ inductive components product line is introducing the high clearance/creepage distance isolation power transformer Model HCT Series. These AEC-Q200 compliant high-voltage isolation push-pull transformers ...

Read more...