Opto-Electronics


LED holders for front panel assembly

8 March 2006 Opto-Electronics

Fischer Elektronik offers an extended range of LED holders for front panel assembly. The LED holder is inserted from the front into the front panel and is held there. The front panel should have a thickness between 1,0 and 1,5 mm. The LED is then inserted into the LED holder from the rear and engages in the end position.

These holders are suitable for 3 mm and 5 mm LEDs. The visible outer diameter of the LED holder is 5,6 mm for the 3 mm version and 7,5 mm for the 5 mm version. The overall height is 5,6 mm for the 3 mm LED and 7 mm for the 5 mm LED.

The LED holders are made from black, glass-fibre reinforced polyamide.



Credit(s)



Share this article:
Share via emailShare via LinkedInPrint this page

Further reading:

Automotive-qualified TVS diodes
25 November 2019, Electrocomp , Circuit & System Protection
Bourns announced the release of the Model 15KPA-SD-Q transient voltage suppressor diode series. This series was designed for use in DC bus clamping applications and for the protection of sensitive electronic ...

Read more...
Robust DC link capacitors
25 November 2019, Electrocomp , Passive Components
TDK’s new B2568* series of EPCOS MKP DC link power capacitors offer high robustness under harsh environmental conditions. The new capacitors are designed for voltages of between 900 and 3000 V d.c. and ...

Read more...
AC film capacitors
25 November 2019, Electrocomp , Passive Components
The B3237x FilterCaps MKD range of EPCOS AC film capacitors from TDK offer a 200 to 1000 VRMS voltage range, a 2475 V d.c. maximum voltage rating, and a ±5% tolerance. The B3237x series is available in ...

Read more...
Image sensor evaluation kits
25 November 2019, Future Electronics , Opto-Electronics
Ams has released the NanoVision and NanoBerry evaluation kits, which provide a ready-made platform for the development of innovative solutions based on the ams NanEyeC miniature image sensor. The NanEyeC ...

Read more...
Waterproof Micro USB connector
23 October 2019, Electrocomp , Interconnection
As part of a new product line from GCT, the aquanex waterproof range brings together high-performance USB connectors with IP67 rated sealing. The first connector launched from the aquanex range, the USB3500, ...

Read more...
Automotive dead reckoning module
25 November 2019, Electrocomp , Telecoms, Datacoms, Wireless, IoT
The MC-1612-DG, made by Locosys, is a single-band multi-system with an Arm base processor. It not only supports GPS, GLONASS, Galileo, QZSS and SBAS, but also has a Flash memory, TCXO, RTC crystal, LNA ...

Read more...
Waterproof Micro USB connector
25 November 2019, Electrocomp , Interconnection
As part of a new product line from GCT, the aquanex waterproof range brings together high-performance USB connectors with IP67 rated sealing. The first connector launched from the aquanex range, the USB3500, ...

Read more...
Magnetic jacks of all trades
25 November 2019, Electrocomp , Interconnection
Molex magnetic jacks incorporate wire-wound components (magnetics) in standard RJ45 jacks. These integrated magnetics, resistors and/or capacitors filter common-mode noise to provide signal integrity, ...

Read more...
Robust DC link capacitors
25 November 2019, Electrocomp , Passive Components
TDK’s new B2568* series of EPCOS MKP DC link power capacitors offer high robustness under harsh environmental conditions. The new capacitors are designed for voltages of between 900 and 3000 V d.c. and ...

Read more...
High-speed data line protectors
25 November 2019, Electrocomp , Circuit & System Protection
Bourns announced the release of the Model TBU-DF055-100-WH, TBU-DF055-200-WH, TBU-DF085-100-WH and TBU-DF085-200-WH bidirectional, dual-channel, High-Speed Protectors (HSPs) for use in data line protection. The ...

Read more...