High-power M12 connectors
20 March 2013
Interconnection
Molex recently introduced the Brad M12 power connector system to meet the demand for higher power consumption requirements of control, sensing and actuators in automation control systems, while maintaining a small footprint.
Submitted for IEC and ANSI/EIA acceptance, Molex aims to establish an open-industry connector standard to increase adoption among a wide array of platforms and manufacturers.
Designed for factory automation applications requiring up to 630 V and 16 A – three times the power of standard M12 connectors – Brad M12 power connectors accommodate the common wire gauge sizes used in power applications.
The connector system provides robust keying and polarisation for enhanced performance and blind mating, plus enclosed electrical contacts for finger safety; connectors are available with 4-pin and 4-pin plus PE (protective earth) ground pin.
The IP67-sealed interface ensures a sealed connection, ideal for use in harsh and wet industrial environments. For additional system safety, the centre (AC version) or 4th pin (DC version) PE ground pin provides first-mate-last-break engagement.
The connectors are available in AC (630 V, 12 A, 2 to 4 pins plus PE ground pin) and DC (63 V, 16 A, 2 to 4 pins with optional PE ground pin) versions. The AC version carries 630 V (2Y(120/208 V), 3Y(277/480 V) and 3D(120/208/240V)) power circuits (pins for L1, L2, L3, N plus PE ground circuits), while the DC version accommodates up to 2 DC power circuits (2x V-/2x V+) or 1 DC circuit plus PE.
For more information contact Roger Young, Molex, +27 (0)72 327 1012, [email protected], www.molex.com
Further reading:
Designing with PCIe
Spectrum Concepts
Editor's Choice Interconnection
PCI Express has become the backbone of modern high-performance systems with each new generation promising higher bandwidth, but that performance comes with a cost.
Read more...
Connectivity solutions for hydrogen technologies
Hiconnex
Interconnection
As the production distribution and utilisation of hydrogen continue to scale, connectivity becomes a key enabler for efficient energy transmission, data communication, and system control.
Read more...
Robust single-pole power connectivity
Hiconnex
Interconnection
Designed for cable-to-cable and cable-to-equipment use, Radiall’s single-pole power connector support current ratings from 250 A to 750 A and operating voltages up to 1000 V AC or DC.
Read more...
M12 push-pull connectors
IOT Electronics
Interconnection
Phoenix Contact’s M12 push-pull connectors with internal locking set a new benchmark for fast, secure, and space-saving connectivity in industrial automation.
Read more...
Versatile outdoor waterproof connectors
Vepac Electronics
Interconnection
The LP-20 outdoor waterproof connector series offers a versatile range of rugged, circular connectors with 2, 3, 4, 5, 7, 8, 9, 12 and 14-pin configurations.
Read more...
Comprehensive range of data connectors
IOT Electronics
Interconnection
Phoenix Contact’s comprehensive range of data connectors provides reliable connection solutions for modern networked applications across industrial, infrastructure, and commercial environments.
Read more...
Compact inline connector for aerospace
Hiconnex
Interconnection
Radiall’s Small Inline Connector series is a fully qualified wire-to-wire solution designed to simplify harness creation, installation, and modification in aerospace applications.
Read more...
Compact hybrid power storage connector
IOT Electronics
Interconnection
Phoenix Contact has introduced a new hybrid connector for electrical energy storage systems, designed to combine power, signal, and data transmission in a single, compact interface.
Read more...
MIL-spec connector series
Future Electronics
Interconnection
The MIL-HD2 connector series from Amphenol is the company’s next-generation, SOSA-aligned solution engineered to meet the most demanding requirements of modern military embedded systems.
Read more...
DC connectors approved for 2000 V
IOT Electronics
Interconnection
Phoneix Contact’s Sunclix DC connectors are now approved for system voltages of up to 2000 V in accordance with TÜV Rheinland’s new test specification, opening the door to higher-voltage PV designs and reduced system costs.
Read more...
printer friendly version