RF Design

Tel: +27 21 555 8400
Email: [email protected]
www: www.rfdesign.co.za
more information about RF Design

Q-band chip attenuators
25 March 2020, RF Design, Telecoms, Datacoms, Wireless, IoT

The TT5 series from Smiths Interconnect are Q-band chip attenuators that operate from DC to 18 GHz. The broadband attenuators are available in attenuation values from 0 to 20 dB in 0,5 dB increments and ...
read more


Sub-harmonic RF mixer
25 March 2020, RF Design, Telecoms, Datacoms, Wireless, IoT

The CMD310C3 is a sub-harmonically pumped mixer die with an integrated LO amplifier housed in a leadless 3 x 3 mm surface-mount QFN package. Produced by Custom MMIC, the CMD310C3 can be used as an up-converter ...
read more


GaN PAs and xPON video receiver
25 March 2020, RF Design, Telecoms, Datacoms, Wireless, IoT

Qorvo announced the latest additions to its innovative RF portfolio of GaN power amplifiers and FTTH xPON video receivers, which serve a wide range of radar, electronic warfare, satellite, 5G and DOCSIS ...
read more


IQ mixers in SMT packaging
25 March 2020, RF Design, Telecoms, Datacoms, Wireless, IoT

The MMIQ-0218 is, according to its manufacturer, Marki Microwave, the only 2 to 18 GHz IQ mixer available in the world, enabling architectures for electronic warfare that were otherwise impossible. Building ...
read more


Review of Class AB high-power amplifiers
25 March 2020, RF Design, Telecoms, Datacoms, Wireless, IoT

A Class AB amplifier is a highly used amplifier design for high-power RF applications, as well as other applications that require high power gain with minimal signal distortion. The main benefit is ...
read more


PMICs for demanding applications
25 March 2020, RF Design, Power Electronics / Power Management

Qorvo recently introduced two power management ICs (PMICs) that can be pre-programmed during manufacture to suit different system requirements and further optimised in the field using firmware via the ...
read more


Front end module for RF range extension
26 February 2020, RF Design, Telecoms, Datacoms, Wireless, IoT

The nRF21540 is a ‘plug and play’ range extender offering enhanced link robustness with an integrated power amplifier (PA)/low noise amplifier (LNA) for use in Nordic Semiconductor’s low-power, short-range ...
read more


Full IoT hardware and software platform
26 February 2020, RF Design, Telecoms, Datacoms, Wireless, IoT

The Taoglas EDGE Connect solution is a next-generation IoT hardware and software platform that provides full cellular, Bluetooth and GPS capabilities with sensor integration – all from an ultra-low-power ...
read more


Patch antenna for positioning
26 February 2020, RF Design, Telecoms, Datacoms, Wireless, IoT

The ADFGP.25A from Taoglas is an embedded dual-pin patch antenna that covers GPS L1, GLONASS L1CR and L1PT, Galileo E2 and L1, and BeiDou B1 bands. It delivers a gain of over 32,8 dB with a 3 V supply ...
read more


BT 5 module supports NFC, Thread and Zigbee
26 February 2020, RF Design, Telecoms, Datacoms, Wireless, IoT

The BMD-341 from u-blox is a standalone Bluetooth 5 module that supports NFC, Thread and Zigbee (IEEE 802.15.4) connectivity for portable, extremely low-power embedded systems. This module is based ...
read more


Fixed-frequency RF synthesiser
26 February 2020, RF Design, Telecoms, Datacoms, Wireless, IoT

The LT-2672-02 from EM Research is a fixed-frequency synthesizer that generates an output signal at 2672,5 MHz using an external 100 MHz reference. It generates a signal that has an output power of 15 dBm ...
read more


Waveguide electromechanical relay switches
26 February 2020, RF Design, Switches, Relays & Keypads

Pasternack has just launched a new series of double ridge waveguide electromechanical relay switches which perform over broader frequency bands, making them ideal for applications involved with electronic ...
read more





<< First   < Previous   Page 28 of 131   Next >   Last >>







While every effort has been made to ensure the accuracy of the information contained herein, the publisher and its agents cannot be held responsible for any errors contained, or any loss incurred as a result. Articles published do not necessarily reflect the views of the publishers. The editor reserves the right to alter or cut copy. Articles submitted are deemed to have been cleared for publication. Advertisements and company contact details are published as provided by the advertiser. Technews Publishing (Pty) Ltd cannot be held responsible for the accuracy or veracity of supplied material.




© Technews Publishing (Pty) Ltd | All Rights Reserved