Computer/Embedded Technology


Programmable Ethernet board

4 February 2015 Computer/Embedded Technology Telecoms, Datacoms, Wireless, IoT

The EM1001 is Tibbo’s most powerful and versatile BASIC-programmable Ethernet board. It features a 10/100 BaseT Ethernet port, four serial ports, onboard Flash disk, EEPROM, and real-time clock with optional backup supercapacitor.

The board can control the GA1000 Wi-Fi add-on, as well as an external LCD, keypad, buzzer and many other peripheral components. It has a 12 V – 3,3 V switching power regulator, RJ45 connector with magnetics, three LEDs, and the MD button.

Since it does not require a host board to plug into, the EM1001 is equally suited to low-volume production devices and hobbyist projects alike.

For more information contact Andrew Hutton, RF Design, +27 (0)21 555 8400, [email protected], www.rfdesign.co.za



Credit(s)



Share this article:
Share via emailShare via LinkedInPrint this page

Further reading:

Rugged, I/O-rich NVIDIA Jetson solutions
Electronic Products Design Computer/Embedded Technology
Developed for the NVIDIA Jetson AGX Orin, the Osbourne carrier and development kit is a compact and rugged platform designed to support a wide range of embedded AI and edge computing applications.

Read more...
Choosing a GNSS receiver
RF Design Telecoms, Datacoms, Wireless, IoT
Applications requiring sub-ten-meter positioning accuracy today can choose between single-band or dual-band technology. While this decision might seem as simple as flipping a coin, it is far from that.

Read more...
Why GNSS positioning precision is enabling the next wave of IoT applications
iCorp Technologies Editor's Choice Telecoms, Datacoms, Wireless, IoT
While high-performance GNSS implementations are achievable with few limitations, most real-world applications must balance power consumption, form factor and accuracy requirements.

Read more...
5G RedCap: Unlocking scalable IoT connectivity
iCorp Technologies Editor's Choice Telecoms, Datacoms, Wireless, IoT
As 2G and 3G networks rapidly sunset across the globe, the Internet of Things (IoT) market faces a critical challenge: how to maintain reliable cellular connectivity without the complexity or cost of full 5G.

Read more...
Is RFoIP technology the future for signal transportation for Satcom applications?
Accutronics Editor's Choice Telecoms, Datacoms, Wireless, IoT
RFoF technology continues to be used for successful IF signal transportation in the ground segment and there is widespread belief that it will be for some time to come, especially for critical communications applications.

Read more...
New generation of SBCs
Computer/Embedded Technology
HardKernel’s new generation of ODROID H4-series SBCs are more powerful; offering higher performance and richer interfaces than previous generations.

Read more...
Smallest 13th gen Intel SBC
Vepac Electronics Computer/Embedded Technology
At just 86 x 55 mm, the de next-RAP8 continues AAEON’s run of producing record-breaking single-board computers with embedded Intel technology.

Read more...
Nordic Semiconductor acquires Memfault
RF Design News
With this acquisition, Nordic has launched its first complete chip-to-cloud platform for lifecycle management of connected products.

Read more...
Satellite IoT through non-terrestrial networks
Future Electronics Editor's Choice Telecoms, Datacoms, Wireless, IoT
Non-terrestrial networks fill cellular coverage gaps in remote areas by extending terrestrial networks and are not subject to disruptions from natural disasters or sabotage.

Read more...
Versatile PoE extender
Vepac Electronics Computer/Embedded Technology
The GP-101ET PoE+ Extender is a 1-port Gigabit PoE extender with plug and play installation requiring neither configuration nor extra electrical power.

Read more...









While every effort has been made to ensure the accuracy of the information contained herein, the publisher and its agents cannot be held responsible for any errors contained, or any loss incurred as a result. Articles published do not necessarily reflect the views of the publishers. The editor reserves the right to alter or cut copy. Articles submitted are deemed to have been cleared for publication. Advertisements and company contact details are published as provided by the advertiser. Technews Publishing (Pty) Ltd cannot be held responsible for the accuracy or veracity of supplied material.




© Technews Publishing (Pty) Ltd | All Rights Reserved