Technical Literature


Hittite Product Selection Guide

24 July 2013 Technical Literature

The May 2013 edition of Hittite’s Product Selection Guide summarises over 1095 products including 22 new products. It organises the portfolio by product line, covering ICs, modules, subsystems and instrumentation for technically demanding digital, RF, microwave and millimetre-wave applications covering DC to 110 GHz.



Credit(s)



Share this article:
Share via emailShare via LinkedInPrint this page

Further reading:

V2X transceiver modules
30 September 2020, RF Design , Telecoms, Datacoms, Wireless, IoT
The VERA-P3 Series from u-blox are automotive grade 802.11p V2X (vehicle-to-everything) transceiver modules that operate in the 5,9 GHz frequency band. These automotive-grade modules are based on the ...

Read more...
Permanent mounting MIMO antenna for Wi-Fi
30 September 2020, RF Design , Telecoms, Datacoms, Wireless, IoT
The Ultima MA530 MIMO antenna from Taoglas is a low-profile, heavy-duty, fully IP67 waterproof external M2M antenna for use in transportation and remote monitoring applications. It provides high efficiency ...

Read more...
Applications for RF electromechanical relay switches
30 September 2020, RF Design , Telecoms, Datacoms, Wireless, IoT
RF electromechanical switches are a key active device in many signal chains, including time-domain duplex communications and pulsed radar applications. Such switches can be as simple as a 3-port toggle ...

Read more...
Diplexer for GNSS L1 and L2
31 August 2020, RF Design , Telecoms, Datacoms, Wireless, IoT
The Taoglas DXP.01.A is a diplexer for GNSS L1 and L2. This advanced compact SAW diplexer is for use in any navigation system application using the GPS/GALILEO L1, GLONASS L2 and BeiDou B2 bands. The ...

Read more...
Miniature SMT noise sources
31 August 2020, RF Design , Test & Measurement
Pasternack has released a new series of miniature SMT packaged noise sources that are ideal for built-in test equipment, dithering for increased dynamic range of A/D converters and as a source for bit ...

Read more...
Directional coupler
31 August 2020, RF Design , Telecoms, Datacoms, Wireless, IoT
The MC16-0222SM from Marki Microwave is a directional coupler with frequency DC to 22 GHz, coupling 16&nbspdB, directivity 14 to 23&nbspdB, insertion loss 1,2 to 3,5&nbspdB, and operating temperature ...

Read more...
Bluetooth wearable tags for social distancing
31 August 2020, RF Design , Telecoms, Datacoms, Wireless, IoT
Nordic Semiconductor has announced that DigitalAlerts, an Eindhoven, Netherlands-based designer and manufacturer of smart digital warning systems, has selected Nordic’s nRF51822 Bluetooth Low Energy (Bluetooth ...

Read more...
RF variable attenuator
31 August 2020, RF Design , Telecoms, Datacoms, Wireless, IoT
The 4205A-95.5 from API Technologies – Weinschel is a Programmable Attenuator that operates from 0,3 to 6000 MHz. It has an attenuation range from 0 to 95,75 dB with 0,25 dB steps, an insertion loss of ...

Read more...
PIN diode SPST switch
29 July 2020, RF Design , Telecoms, Datacoms, Wireless, IoT
The F192A from Kratos is a non-reflective PIN diode SPST (single pole, single throw) switch that operates from 0,2 to 18 GHz. This high-speed switch has an insertion loss of less than 3,5 dB with isolation ...

Read more...
LTE Cat. 1 module with 3G fallback
29 July 2020, RF Design , Telecoms, Datacoms, Wireless, IoT
The LARA-R281 from u-blox is an LTE Cat 1 Module with 3G fallback connectivity for operation in Europe (EMEA). It supports the LTE bands (1, 3, 8, 20 and 28) used by the European MNOs for LTE services ...

Read more...