Passive Components


One piece SMD inductors

13 July 2005 Passive Components

Neosid does not use glue to mount inductor bobbins onto their base plates. Instead, it fabricates both parts in one piece, as ferrite components. This is made possible through the company's special injection-moulding process that allows it to produce ferrites in all shapes. In this way, troublesome faults that occur during bonding and at the gluing points, are avoided.

A secondary advantage is that the metal clips, soldering pins, and the plating thereof, are not required. The lead-out wires of the coil windings are simply tinned and so they then act as the SMD soldering points for mounting onto the PCBs.

The compact design of Neosid's new serties of fixed inductors - the MS 50, MS 85, MS 40 and MS 42 - means that they only require a minimum of space. Another advantage is their small stray field. Inductances from 10 nH to 150 mH are possible with currents up to 7 A.

Applications are typically for: interference suppression, DC-DC converters, decoupling in high frequency circuits and motor vehicle electronics.



Credit(s)



Share this article:
Share via emailShare via LinkedInPrint this page

Further reading:

Low-profile aluminium electrolytic capacitors
25 November 2019, TRX Electronics , Passive Components
At 2 and 3 mm thin, Cornell Dubilier’s ULP series offers high energy density in a low-profile aluminium electrolytic capacitor. Designed specifically for applications requiring bulk capacitance and the ...

Read more...
Automotive-qualified TVS diodes
25 November 2019, Electrocomp , Circuit & System Protection
Bourns announced the release of the Model 15KPA-SD-Q transient voltage suppressor diode series. This series was designed for use in DC bus clamping applications and for the protection of sensitive electronic ...

Read more...
Robust DC link capacitors
25 November 2019, Electrocomp , Passive Components
TDK’s new B2568* series of EPCOS MKP DC link power capacitors offer high robustness under harsh environmental conditions. The new capacitors are designed for voltages of between 900 and 3000 V d.c. and ...

Read more...
AC film capacitors
25 November 2019, Electrocomp , Passive Components
The B3237x FilterCaps MKD range of EPCOS AC film capacitors from TDK offer a 200 to 1000 VRMS voltage range, a 2475 V d.c. maximum voltage rating, and a ±5% tolerance. The B3237x series is available in ...

Read more...
Waterproof Micro USB connector
23 October 2019, Electrocomp , Interconnection
As part of a new product line from GCT, the aquanex waterproof range brings together high-performance USB connectors with IP67 rated sealing. The first connector launched from the aquanex range, the USB3500, ...

Read more...
Automotive dead reckoning module
25 November 2019, Electrocomp , Telecoms, Datacoms, Wireless, IoT
The MC-1612-DG, made by Locosys, is a single-band multi-system with an Arm base processor. It not only supports GPS, GLONASS, Galileo, QZSS and SBAS, but also has a Flash memory, TCXO, RTC crystal, LNA ...

Read more...
High-power chip resistors
25 November 2019, TRX Electronics , Passive Components
Panasonic has released a line of resistors to help engineers produce cheaper, smaller and more efficient designs. The legacy resistors of the ERJ series have been made smaller while handling the same ...

Read more...
Waterproof Micro USB connector
25 November 2019, Electrocomp , Interconnection
As part of a new product line from GCT, the aquanex waterproof range brings together high-performance USB connectors with IP67 rated sealing. The first connector launched from the aquanex range, the USB3500, ...

Read more...
Magnetic jacks of all trades
25 November 2019, Electrocomp , Interconnection
Molex magnetic jacks incorporate wire-wound components (magnetics) in standard RJ45 jacks. These integrated magnetics, resistors and/or capacitors filter common-mode noise to provide signal integrity, ...

Read more...
High-current power shunts
25 November 2019, TRX Electronics , Passive Components
Ideal for high-current applications, the PSx series of shunts has been expanded by KOA. Built using a solid metal alloy resistance element with copper terminations, the device also has a low temperature ...

Read more...