Opto-Electronics


Tubular fluorescent lamp drivers

21 March 2012 Opto-Electronics

NXP Semiconductors has announced the UBA2016A, a dimmable fluorescent lamp driver IC for high-frequency tube lamps (HF-TL) combining power factor correction (PFC) controller and ballast driver circuits. Using its boost function, high-end commercial-grade, amalgam-based tube lamps will have a run-up time almost similar to mercury-based tube lamps. The fully integrated dimming function enables tube lamps to be dimmed gradually for a better sensory experience and for energy saving.

Based on NXP GreenChip technology, the new family of fluorescent driver ICs consist of non-dimmable mainstream (UBA2015), dimmable (UBA2015A) and dimmable-boosted (UBA2016A) solutions, supporting all common lamp types (T4, T5, T8, T12) and lamp configurations, including multi-lamp and multi-power solutions.

The ICs drive a half-bridge circuit made of two MOSFETs with a supply voltage of up to 600 V and a PFC stage using one MOSFET. The family also features very low standby power ­levels (<100 mW), which further enhances energy efficiency. The many built-in protections support all standards, and meet industry requirements for reliability (including end-of-life protections) and performance. The ICs are available in both SO and DIP packages, and feature adjustable current controlled preheat and accurate lamp current control (±1%).

For more information contact EBV Electrolink, +27 (0)21 402 1940, [email protected], www.ebv.com



Credit(s)



Share this article:
Share via emailShare via LinkedInPrint this page

Further reading:

High-reliability isolation amplifiers
EBV Electrolink Analogue, Mixed Signal, LSI
The VIA series of isolation amplifiers from Vishay are designed to deliver exceptional thermal stability and precise measurement capabilities.

Read more...
Heat-resistant LEDs
Opto-Electronics
Würth Elektronik’s new RGB LEDs are characterised by excellent heat resistance with an insensitivity to temperatures from -40 to 100°C making them ideal solutions for reliable, colour-variable lighting in applications at high operating temperatures.

Read more...
PhotoMOS relays
Future Electronics Opto-Electronics
The AQY221R2SX and AQY221R2S PhotoMOS from Panasonic Industry ensures excellent characteristics and high-speed switching performance.

Read more...
Mouser now shipping onsemi’s image sensors
TRX Electronics Opto-Electronics
The AR0145CS is a 1/4,3-inch CMOS digital image sensor with a 1280 (H) x 800 (V) active-pixel array that can capture both continuous video and single frames.

Read more...
Adaptive optics’ power solution
Altron Arrow Opto-Electronics
Vicor power-dense adaptive optical modules enable colossal telescopes to look into the past for deep space discoveries.

Read more...
Ultra-high speed photo detection
Opto-Electronics
TDK Corporation has announced a photo-spintronic conversion element combining optical, electronic, and magnetic elements that can respond at an ultra-high speed of 20 picoseconds.

Read more...
High-speed lasers
RFiber Solutions Opto-Electronics
Macom are a high-volume manufacturer of lasers, deploying more than 100 million devices with a reliability of less than 50 FIT and greater than 100 years of wear-out lifetime

Read more...
High-performance optical interconnect
Opto-Electronics
STMicroelectronics has unveiled its next generation of proprietary technologies for higher-performing optical interconnect in datacentres and AI clusters.

Read more...
First NVMe SSD Built with 8th-gen BiCS FLASH
EBV Electrolink Computer/Embedded Technology
KIOXIA recently announced the development and prototype demonstration of its new KIOXIA CM9 Series PCIe 5.0 NVMe SSDs, which incorporates CMOS directly Bonded to Array technology.

Read more...
IMU with dual-sensing capability
EBV Electrolink Analogue, Mixed Signal, LSI
ST’s 6-axis inertial measurement unit integrates a dual accelerometer up to 320g and embedded AI for activity tracking and high-impact sensing.

Read more...









While every effort has been made to ensure the accuracy of the information contained herein, the publisher and its agents cannot be held responsible for any errors contained, or any loss incurred as a result. Articles published do not necessarily reflect the views of the publishers. The editor reserves the right to alter or cut copy. Articles submitted are deemed to have been cleared for publication. Advertisements and company contact details are published as provided by the advertiser. Technews Publishing (Pty) Ltd cannot be held responsible for the accuracy or veracity of supplied material.




© Technews Publishing (Pty) Ltd | All Rights Reserved