Differential line drivers
13 June 2012
Analogue, Mixed Signal, LSI
The LS7272/LS7273 from LSI/CSI are short circuit-proof quad differential industrial power line drivers. They can operate up to 30 V and have a selectable thermal shutdown feature.
The data inputs are TTL/CMOS compatible and can be a driver up to the supply voltage. An input can be used to place all the outputs in a high-impedance state, while another input on the 7272 is used to connect the outputs as push-pull drivers or open-drain drivers, where the outputs can be returned through external loads to a maximum of the supply voltage. For the 7273, this pin is tied to ground; the outputs are open-drain and the loads can be returned to any voltage between 4,5 V and 30 V independent of the supply voltage.
An internal 5 V regulated supply is used to power the logic and level converter blocks. Upon power-up, a power-on-reset (POR) circuit block forces all output drivers to the high-impedance state until the power supply voltage reaches a nominal 3,8 V. Included in the POR circuit block is an hysteresis of 100 mV such that if the power supply drops below 3,7 V all output drivers are forced to the high-impedance state until the voltage rises above 3,8 V.
Further reading:
High-speed PIN diode
Altron Arrow
Analogue, Mixed Signal, LSI
Vishay’s new high-speed Silicon PIN diode is able to detect both visible and near infra-red radiation over a wide spectrum range from 350 to 1100 nm.
Read more...
Analogue front end for sensor measurements
Electrocomp
Analogue, Mixed Signal, LSI
The NJU9103 AFE from Nisshinbo is a tiny analogue front end, with a 16-bit resolution ADC and up to 512 x signal amplification from the programmable gain amplifier.
Read more...
Single-channel software configurable I/O
Altron Arrow
Analogue, Mixed Signal, LSI
These use cases of the AD74115H include analogue output and input, digital output and input, resistance temperature detector (RTD), and thermocouple measurement capability.
Read more...
Current-sense amplifier with PWM rejection
Altron Arrow
Analogue, Mixed Signal, LSI
Analog Devices’ AD8410A is a high voltage, high bandwidth current-sense amplifier that features an initial gain of 20 V/V and a 2,2 MHz bandwidth.
Read more...
Combining a LPF and ADC driver for a 20 Vp-p signal
Altron Arrow
Analogue, Mixed Signal, LSI
A mixed-signal ADC driver circuit’s optimum performance depends on multiple variables: the driver’s settling time, the RC filter’s time constant, driving impedance, and the ADC sampling capacitor’s kickback current, all interact during acquisition time and contribute towards sampling errors.
Read more...
Pressure sensor with NextNav certification
EBV Electrolink
Analogue, Mixed Signal, LSI
STMicroelectronics’ LPS22DF pressure sensor has received a NextNav certification, which guarantees performance and reliability for geolocation and other types of applications.
Read more...
Reference design for Raspberry Pi analogue I/O
Analogue, Mixed Signal, LSI
Analogue Devices has published a reference design for ±10 V analogue input and ±15 V analogue output for Raspberry Pi platforms.
Read more...
Multi-zone distance sensor with 90° field of view
Avnet Silica
Analogue, Mixed Signal, LSI
STMicroelectronics has revealed a new FlightSense multi-zone distance sensor, with 90° field of view, to bring lifelike situational awareness to applications like home automation, computers, robots, and smart equipment.
Read more...
Six-axis IMU with Qvar sensing channel
Altron Arrow
Analogue, Mixed Signal, LSI
The LSM6DSV16X from STMicroelectronics is a high-performance, low-power six-axis IMU, featuring a three-axis digital accelerometer and a three-axis digital gyroscope.
Read more...
Bidirectional current-sense amplifier with PWM
RS South Africa
Analogue, Mixed Signal, LSI
The MAX49925 from Analogue Devices is a bidirectional current-sense amplifier (CSA) with an input common-mode range that extends from -40 to 76 V, making it suitable for 48 V HEV applications where there are large automotive transients.
Read more...
printer friendly version