Micrel announced the Ripple Blocker family comprising the MIC94300 voltage follower output and the MIC94310 fixed-output, low-dropout (LDO) IC. The devices reduce switching regulator output ripple and harmonics by 60 dB at high frequencies.
The devices were developed to provide more efficient noise suppression for today’s highly sensitive data and image capturing systems. The MIC94300 integrates a low-RDS(ON), current-limit switch and a low-pass filter that passes DC and blocks the AC component of the input voltage. The MIC94310 is a high-performance LDO that offers better power supply rejection ratio performance from DC to 5 MHz than discrete solutions.
Micrel’s new Ripple Blocker technology improves minimum detectable signal capturing for low-light image sensors by suppressing system power ripple for the Image System Processor (ISP). By eliminating the large LC filter that would typically be required to reduce ripple in a discrete solution, the MIC943XX series devices provide more usable board space to accommodate space-constrained designs. In addition, this new series offers an operating input range of 1,8 V to 3,6 V with exceptional transient performance, ultra-low dropout and very high PSRR (80 dB at 1 kHz).
Both ICs feature an active-high enable pin for power sequencing. They deliver up to 200 mA, with higher-current devices under development. The devices offer full current and thermal fault condition protection and the MIC94310 offers low dropout of 17 mV. They also feature a -40°C to 125°C junction temperature range. Package options include 0,88 x 0,88 mm, 4-bump CSP and 1,2 x 1,6 mm Thin-MLF.
Quality batteries are critical for IIoT Uniross Batteries
Power Electronics / Power Management
Batteries intended for use in industrial operations must indeed offer complete reliability under extreme environmental conditions, resistance to vibration and harsh environments.
Read more...12 kW hybrid inverter
Power Electronics / Power Management
Sungrow recently unveiled its next-generation residential energy storage solution, expanding its power range from 5 kW to 12 kW with the introduction of the new MG12RL hybrid inverter.
Read more...40 W and 75 W railway DC/DC converter Brabek
Power Electronics / Power Management
RECOM has announced two new cost-efficient DC/DC converters for the rail market with an ultra-wide 11:1 input range to cover all nominal input voltages from 24 to 110 V DC.
Read more...Power modules for solid-state transformers RS South Africa
Power Electronics / Power Management
Microchip’s new 3,3 kV silicon carbide modules deliver the required thermal performance and efficiency for SSTs to increase power available for token generation.
Read more...Solving South African power problems with locally built intelligence
Editor's Choice Power Electronics / Power Management
Smart metering infrastructure in South Africa remains patchy. The rollout has been slow, coverage is inconsistent, and for the most part, granular per-unit measurement simply does not exist.
Read more...Wide range power module
Power Electronics / Power Management
The latest DC-DC modules from Würth Elektronik are characterised by high resilience to voltage transients on the 24 V bus and an extremely wide input-voltage range from 3,5 V to 38 V.
Read more...Powering smart sensor networks CST Electronics
Telecoms, Datacoms, Wireless, IoT
NeoCortec’s NeoMesh wireless mesh networking protocol and software stack is ideally suited for powering smart sensor networks where each device is required to send and receive small packets of data infrequently, but with high reliability.
Read more...Selecting primary batteries for maximum service life Uniross Batteries
Power Electronics / Power Management
Primary batteries play an important role in IoT applications. Designed for longevity, they have a high-energy capacity and are often used in standalone applications where charging is impractical or impossible.
Read more...4 kW e-mobility DC-DC converter Brabek
Power Electronics / Power Management
The RECOM RMOD4000 series of compact, plug-and-play DC-DC converters is a cost-effective solution to provide isolated 14 V, 28 V, or 56 V DC network rails from a high input voltage between 180 and 950 V DC.
Read more...Aluminium case upgrade boosts performance Vepac Electronics
Power Electronics / Power Management
The SQBF Quarter Brick 300 W DC to DC Converter is now available in a newly upgraded metal case designed to deliver improved durability and superior electrical performance across demanding applications.
While every effort has been made to ensure the accuracy of the information contained herein, the publisher and its agents cannot be held responsible for any errors contained, or any loss incurred as a result. Articles published do not necessarily reflect the views of the publishers. The editor reserves the right to alter or cut copy. Articles submitted are deemed to have been cleared for publication. Advertisements and company contact details are published as provided by the advertiser. Technews Publishing (Pty) Ltd cannot be held responsible for the accuracy or veracity of supplied material.
printer friendly version