Top-port MEMS microphones

20 March 2013 Analogue, Mixed Signal, LSI

New from TDK are the EPCOS C920 and C923 top-port MEMS microphones with footprints of only 2,75 x 1,85 mm and an insertion height of 0,9 mm.

Thanks to their design, the air volume in the microphones is small, so that no resonances occur in the 10 kHz range, resulting in outstanding audio quality with a flat frequency response.

The microphones have a very good signal-to-noise ratio of 56 dB (C920) and 57 dB (C923) respectively. The C923 type offers a very flat frequency response even in the lowest frequency range of the audio spectrum. A high-pass filter that suppresses frequencies below 100 Hz is integrated into the C920 microphone. This means that no wind noise is transmitted, for instance.

At supply voltages of between 1,64 and 3,6 V d.c., current consumption is only 125 μA. These RoHS-compatible components have an output impedance of 260 Ω.

Further reading:

High-speed PIN diode
Altron Arrow Analogue, Mixed Signal, LSI
Vishay’s new high-speed Silicon PIN diode is able to detect both visible and near infra-red radiation over a wide spectrum range from 350 to 1100 nm.

Read more...

---

Analogue front end for sensor measurements
Electrocomp Analogue, Mixed Signal, LSI
The NJU9103 AFE from Nisshinbo is a tiny analogue front end, with a 16-bit resolution ADC and up to 512 x signal amplification from the programmable gain amplifier.

Read more...

---

Single-channel software configurable I/O
Altron Arrow Analogue, Mixed Signal, LSI
These use cases of the AD74115H include analogue output and input, digital output and input, resistance temperature detector (RTD), and thermocouple measurement capability.

Read more...

---

Current-sense amplifier with PWM rejection
Altron Arrow Analogue, Mixed Signal, LSI
Analog Devices’ AD8410A is a high voltage, high bandwidth current-sense amplifier that features an initial gain of 20 V/V and a 2,2 MHz bandwidth.

Read more...

---

Combining a LPF and ADC driver for a 20 Vp-p signal
Altron Arrow Analogue, Mixed Signal, LSI
A mixed-signal ADC driver circuit’s optimum performance depends on multiple variables: the driver’s settling time, the RC filter’s time constant, driving impedance, and the ADC sampling capacitor’s kickback current, all interact during acquisition time and contribute towards sampling errors.

Read more...

---

Pressure sensor with NextNav certification
EBV Electrolink Analogue, Mixed Signal, LSI
STMicroelectronics’ LPS22DF pressure sensor has received a NextNav certification, which guarantees performance and reliability for geolocation and other types of applications.

Read more...

---

Reference design for Raspberry Pi analogue I/O
Analogue, Mixed Signal, LSI
Analogue Devices has published a reference design for ±10 V analogue input and ±15 V analogue output for Raspberry Pi platforms.

Read more...

---

Multi-zone distance sensor with 90° field of view
Avnet Silica Analogue, Mixed Signal, LSI
STMicroelectronics has revealed a new FlightSense multi-zone distance sensor, with 90° field of view, to bring lifelike situational awareness to applications like home automation, computers, robots, and smart equipment.

Read more...

---

Six-axis IMU with Qvar sensing channel
Altron Arrow Analogue, Mixed Signal, LSI
The LSM6DSV16X from STMicroelectronics is a high-performance, low-power six-axis IMU, featuring a three-axis digital accelerometer and a three-axis digital gyroscope.

Read more...

---

Bidirectional current-sense amplifier with PWM
RS South Africa Analogue, Mixed Signal, LSI
The MAX49925 from Analogue Devices is a bidirectional current-sense amplifier (CSA) with an input common-mode range that extends from -40 to 76 V, making it suitable for 48 V HEV applications where there are large automotive transients.

Read more...

---