Energy harvesting and battery charging IC
12 March 2014
Power Electronics / Power Management
A new chip from STMicroelectronics integrates all the functions needed to power electronic circuits and recharge batteries using either a solar cell or thermoelectric generator (TEG).
Harvesting ambient light or thermal energy to power small electronic devices such as wireless sensors, smart building and industrial equipment controls, wellness and wearable monitors, protects the environment by reducing CO2 emissions, while eliminating batteries and power cabling, and enabling the Internet of Things (IoT) ecosystem. In the future, hundreds of millions of these devices operating from tiny quantities of harvested ambient energy are expected to be deployed in environments such as office buildings, houses, hotels, industrial sites, transportation infrastructure and electric vehicles.
ST’s SPV1050 is ideal for applications with power requirements from a few microwatts to several milliwatts, and is equally suitable for both indoor and outdoor consumer and industrial applications using either solar or thermal energy.
Both 1,8 V and 3,3 V regulators are available to power a companion microcontroller or wireless transmitter directly without requiring additional components. Maximum power-point tracking (MPPT) continuously optimises energy harvesting, or can be disabled. The IC’s battery charging circuitry supports a wide variety of battery types including lithium-ion and lithium-polymer, lithium thin-film solid state, NiMH and NiCd, as well as supercapacitors.
Inside the SPV1050, a buck-boost converter allows the device to connect to either TEG or indoor/outdoor solar energy harvesting modules by providing a wide input voltage range from 180 mV to 8 V. Average operating efficiency of 90% allows fast battery charging even at low input power levels, while minimum MPPT accuracy of 90% maximises energy extraction from solar or TEG sources.
In addition, the integrated battery charging controller uses highly accurate under-voltage and end-of-charge thresholds, and provides safe control logic to prevent excessive discharging for longer battery life.
For more information contact Erich Nast, Avnet Kopp, +27 (0)11 319 8600, [email protected], www.avnet.co.za
Further reading:
Quality batteries are critical for IIoT
Uniross Batteries
Power Electronics / Power Management
Batteries intended for use in industrial operations must indeed offer complete reliability under extreme environmental conditions, resistance to vibration and harsh environments.
Read more...
12 kW hybrid inverter
Power Electronics / Power Management
Sungrow recently unveiled its next-generation residential energy storage solution, expanding its power range from 5 kW to 12 kW with the introduction of the new MG12RL hybrid inverter.
Read more...
40 W and 75 W railway DC/DC converter
Brabek
Power Electronics / Power Management
RECOM has announced two new cost-efficient DC/DC converters for the rail market with an ultra-wide 11:1 input range to cover all nominal input voltages from 24 to 110 V DC.
Read more...
Power modules for solid-state transformers
RS South Africa
Power Electronics / Power Management
Microchip’s new 3,3 kV silicon carbide modules deliver the required thermal performance and efficiency for SSTs to increase power available for token generation.
Read more...
Solving South African power problems with locally built intelligence
Editor's Choice Power Electronics / Power Management
Smart metering infrastructure in South Africa remains patchy. The rollout has been slow, coverage is inconsistent, and for the most part, granular per-unit measurement simply does not exist.
Read more...
Wide range power module
Power Electronics / Power Management
The latest DC-DC modules from Würth Elektronik are characterised by high resilience to voltage transients on the 24 V bus and an extremely wide input-voltage range from 3,5 V to 38 V.
Read more...
Selecting primary batteries for maximum service life
Uniross Batteries
Power Electronics / Power Management
Primary batteries play an important role in IoT applications. Designed for longevity, they have a high-energy capacity and are often used in standalone applications where charging is impractical or impossible.
Read more...
4 kW e-mobility DC-DC converter
Brabek
Power Electronics / Power Management
The RECOM RMOD4000 series of compact, plug-and-play DC-DC converters is a cost-effective solution to provide isolated 14 V, 28 V, or 56 V DC network rails from a high input voltage between 180 and 950 V DC.
Read more...
Aluminium case upgrade boosts performance
Vepac Electronics
Power Electronics / Power Management
The SQBF Quarter Brick 300 W DC to DC Converter is now available in a newly upgraded metal case designed to deliver improved durability and superior electrical performance across demanding applications.
Read more...
Extending the range of power converters
RS South Africa
Power Electronics / Power Management
Power Integrations recently announced a breakthrough in flyback topology extending the power range of flyback converters to 440 W - well beyond the limits that traditionally required more complex resonant and LLC topologies.
Read more...
printer friendly version