NuVision Electronics

Tel: +27 11 608 0144
Email: [email protected]
www: www.nuvisionelec.com
more information about NuVision Electronics

Low-power linear regulator
27 January 2016, Power Electronics / Power Management

The MP2019 is a low-power linear regulator that supplies power to systems with high-voltage batteries. It includes a wide 3 V to 40 V input range, low-dropout voltage and a low quiescent supply current. ...
read more


Synchronous buck controller
25 November 2015, Power Electronics / Power Management

The MP2908A is a high-voltage, synchronous step-down (buck) controller that directly steps down voltages from 4 V up to 60 V. Made by Monolithic Power Systems, it employs a PWM current control architecture ...
read more


75 V switching regulator
25 November 2015, Power Electronics / Power Management

The MP4569 from Monolithic Power Systems is a step-down switching regulator with integrated high-side/low-side, high-voltage power MOSFETs. It provides a highly efficient output of up to 0,3 A and its ...
read more


IDE for concurrent wireless and MCU design
25 November 2015, Design Automation

Silicon Labs introduced the latest generation of Simplicity Studio, the company’s integrated development environment (IDE) for concurrent microcontroller (MCU) and RF design. This software release inherits ...
read more


Reference design for voice-enabled ZigBee remote controls
25 November 2015, Telecoms, Datacoms, Wireless, IoT, Design Automation

Silicon Labs has released a cost-effective solution for voice-enabled ZigBee remote controls. This comprehensive reference design solution significantly reduces the need for costly external hardware by ...
read more


Analog front end for NFC
4 November 2015, Telecoms, Datacoms, Wireless, IoT, Analogue, Mixed Signal, LSI

ams announced a new NFC (near field communications) solution for manufacturers of smart watches, wristbands and other space-constrained devices, enabling them to reliably support contactless payments ...
read more


Software stack for Bluetooth audio accessories
14 October 2015, Telecoms, Datacoms, Wireless, IoT

Silicon Labs introduced a sixth-generation version of the iWRAP Bluetooth software stack for the Bluetooth 3.0 wireless audio accessory market. iWRAP 6.1 software is a full-featured embedded Bluetooth ...
read more


Heart rate monitor IC
14 October 2015, Analogue, Mixed Signal, LSI

ams has premiered a new family of health/fitness solutions aimed at wearable devices, with the launch of the AS7000. The solution incorporates a highly integrated optical sensor module accompanied by ...
read more


Isolated current sense amplifier
23 September 2015, Analogue, Mixed Signal, LSI

New from Silicon Labs is a current sense amplifier delivering robust isolation, high bandwidth and low signal delay. The Si8920 provides an ideal current shunt measurement solution for power control ...
read more


Bluetooth Smart module
2 September 2015, Telecoms, Datacoms, Wireless, IoT

Silicon Labs introduced a fully integrated, pre-certified Bluetooth Smart module solution that gives developers a fast path to low-power wireless connectivity for the Internet of Things (IoT). The BGM111 ...
read more


Optimising clock synthesis in small cells and heterogeneous networks
22 July 2015, Telecoms, Datacoms, Wireless, IoT

Mobile network operators are increasingly turning to small cell base stations to expand coverage, increase capacity and enable network densification in congested, high-traffic urban environments. Small ...
read more


Highly integrated clock IC
22 July 2015, Analogue, Mixed Signal, LSI

Silicon Labs’ new Si5380 is the industry’s first clock generator capable of replacing a low phase noise integer-N clock, voltage-controlled crystal oscillator (VCXO), discrete loop filters and voltage ...
read more





<< First   < Previous   Page 13 of 36   Next >   Last >>







While every effort has been made to ensure the accuracy of the information contained herein, the publisher and its agents cannot be held responsible for any errors contained, or any loss incurred as a result. Articles published do not necessarily reflect the views of the publishers. The editor reserves the right to alter or cut copy. Articles submitted are deemed to have been cleared for publication. Advertisements and company contact details are published as provided by the advertiser. Technews Publishing (Pty) Ltd cannot be held responsible for the accuracy or veracity of supplied material.




© Technews Publishing (Pty) Ltd | All Rights Reserved