Concilium Technologies

Tel: +27 12 678 9200
Email: [email protected]
www: www.concilium.co.za/test-measurement
more information about Concilium Technologies

IMD application for RF network analyser
26 November 2008, Concilium Technologies, Test & Measurement

Agilent has announced an intermodulation distortion (IMD) application for its high-performance PNA-X microwave network analyser. The traditional setup for making swept-IMD measurements requires the ...
read more


DMM with OLED display
12 November 2008, Concilium Technologies, Test & Measurement

Agilent has introduced the U1253A handheld digital multimeter (DMM), said to be the first DMM to use an organic light-emitting diode (OLED) display. For on-the-go and benchtop applications, the OLED readout ...
read more


Realtime scope breaks one billion sample barrier
12 November 2008, Concilium Technologies, Test & Measurement

The Infiniium 90000A Series not only claims to offer the world’s deepest acquisition memory depth, but also the world’s first hardware/software integrated triggering system, InfiniiScan Plus, which enables ...
read more


Agilent's power analyser wins four awards
12 November 2008, Concilium Technologies, Test & Measurement

Agilent Technologies announced that its N6705A DC Power Analyser has been awarded four prestigious industry awards:    * Test & Measurement World’s 2008 Best in Test.    * Electronic Products' 2007 Product ...
read more


Thermocouple power sensors
29 October 2008, Concilium Technologies, Telecoms, Datacoms, Wireless, IoT

Agilent has introduced new thermocouple power sensors that offer excellent dynamic range in average-power measurements. As an enhanced replacement for the Agilent 8480 series, the new sensors cover a ...
read more


Agilent acquires low-cost instrument supplier
29 October 2008, Concilium Technologies, News

Agilent Technologies, whose products are locally distributed by Concilium Technologies, has announced a substantial acquisition of the assets of Taiwan-based Escort Instruments, an established supplier ...
read more


Low-cost DC power supplies
1 October 2008, Concilium Technologies, Test & Measurement

Agilent has introduced the U8000 series of single-output, non-programmable DC power supplies, a low-cost expansion of the E3600 series. Beyond cost savings, these DC power supplies offer excellent value ...
read more


New Genesys EDA release from Agilent
3 September 2008, Concilium Technologies, Design Automation

Agilent has announced shipment of the 2008.07 release of its Genesys integrated EDA software platform for self-supporting RF and microwave designers and workgroups. The new release contains improvements ...
read more


Hints for better scope probing
20 August 2008, Concilium Technologies, Test & Measurement

Probing is critical to making quality oscilloscope measurements, and often the probe is the first link in the oscilloscope measurement chain. If probe performance is not adequate for your application, ...
read more


Realtime scope breaks one billion sample barrier
25 June 2008, Concilium Technologies, Test & Measurement

Agilent has broken the one billion acquisition sample (1 Gpts) barrier with its new high­performance oscilloscope. The new Infiniium 90000A Series not only claims to offer the world’s deepest acquisition ...
read more


Hints for better scope probing
30 April 2008, Concilium Technologies, Test & Measurement

Passive or active probe? For general-purpose mid-to-low-frequency (less than 600 MHz) measurements, passive high-impedance resistor divider probes are good choices. These rugged and inexpensive tools ...
read more


Power supply intelligence: mitigating DUT damage
30 April 2008, Concilium Technologies, Power Electronics / Power Management

Today, devices under test (DUT) are often powered by multiple DC input voltages and it is these very same power sources that can cause extensive damage to sensitive DUT circuitry if not turned off in ...
read more





<< First   < Previous   Page 22 of 29   Next >   Last >>







While every effort has been made to ensure the accuracy of the information contained herein, the publisher and its agents cannot be held responsible for any errors contained, or any loss incurred as a result. Articles published do not necessarily reflect the views of the publishers. The editor reserves the right to alter or cut copy. Articles submitted are deemed to have been cleared for publication. Advertisements and company contact details are published as provided by the advertiser. Technews Publishing (Pty) Ltd cannot be held responsible for the accuracy or veracity of supplied material.




© Technews Publishing (Pty) Ltd | All Rights Reserved