Experiments show lead-free pastes will give great results with 0201s
4 October 2006Manufacturing / Production Technology, Hardware & Services
DEK has concluded research into screen printing for 0201 SMT components using SnPb and SAC solder pastes, highlighting new assembly and board design parameters for robust, high-volume assembly with minimal application-specific modifications. Among the observations from analysing a large number of test assemblies post reflow, DEK found that SAC pastes have an inherently wider process window.
Following the research, the optimum pad size for 0201 assembly is now known to be 300 x 380 x 230 µm, with pad-to-pad spacing of 200 µm. No-clean paste and air reflow atmosphere produce the least tombstone defects. Technologies that increase wetting forces, such as nitrogen reflow or water soluble pastes, induce more defects. Better yields were experienced with SAC-based pastes, because the wetting forces are lower with lead-free formulae. "Assembly conditions that promote slower wetting speeds create a larger process window and produce good yield, and this is largely independent of the component orientation," said Clive Ashmore, and one of the leaders of the research team.
After establishing design and process parameters that produced the minimum number of defects, the experiments then applied very challenging assembly scenarios to discover the limits at which defects begin to occur. Pad spacing was also reduced to 100 μm to encourage bridging. In addition, the overlap between the end terminations of the components and the solder paste, which is known as the 'grab', was tested at 150, 100 and 50 μm. To provoke tombstone defects, stencil registration was deliberately offset to create an imbalance in the grab between the two terminations of the same component. Registration errors of 0, 1,0 and 1,5 μm in both x- and y-axes were deliberately applied, to determine tolerances for printing accuracy for successful 0201 assembly.
The results showed that the tombstoning defects caused by increasing stencil offset can be reduced by increasing grab. On the other hand, a large grab increases bridging defects and solder balling. "High printing accuracy and low grab are required to minimise the cumulative defects arising from tombstoning, bridging and solder balling," explained Ashmore.
After printing SAC-based paste at the 4-mil print offset condition, post-reflow yield generally surpassed the performance of the tin-lead eutectic solder assemblies. Tombstoning and solder-balling levels were also significantly lower. "These results show great promise for assembling 0201s with SAC-based pastes," concluded Ashmore.
World-first 016008 mm component placement
Manufacturing / Production Technology, Hardware & Services
Fuji has achieved the world’s first placement of 016008 mm (0,16 x 0,08 mm or 006 x 003 inches) size components on printed circuit boards with its SMT pick and place machine, NXTR.
Read more...Lifecycle and obsolescence: Protecting electronics through process Production Logix
Manufacturing / Production Technology, Hardware & Services
At Production Logix, we believe longevity is not accidental. It is engineered through early visibility, structured response, and disciplined execution, in partnership with our OEM customers.
Read more...Maximising squeegee quality and durability Testerion
Manufacturing / Production Technology, Hardware & Services
Transition Automation has announced two new product advancements designed to improve SMT printing performance and extend squeegee life: laser-enhanced Permalex bonding and integrated edge protectors.
Read more...NeoDen ND2 PCB screen printer ZETECH ONE
Manufacturing / Production Technology, Hardware & Services
The NeoDen ND2 PCB screen printing machine is a fully automatic stencil printer designed to deliver precise and consistent solder paste application in modern SMT production environments.
Read more...Understanding the BGA rework process Techmet
Manufacturing / Production Technology, Hardware & Services
BGA rework is a highly technical process that involves removing the faulty component, preparing the circuit board, and installing a new or repaired device, while maintaining the integrity of the printed circuit board.
Read more...Flexible three-process reflow soldering system Truth Electronic Manufacturing
Manufacturing / Production Technology, Hardware & Services
By combining multiple soldering technologies within a single system, the Vision TripleX system enables manufacturers to adapt easily to different assembly requirements, board designs, and production volumes.
Read more...Inline vapour phase soldering for high-volume production MyKay Tronics
Manufacturing / Production Technology, Hardware & Services
The VP2200-100 vacuum inline vapour phase soldering system from ASSCON is designed for fully automated, high-volume electronics manufacturing where process consistency and solder joint quality are critical.
Read more...Global electronics solutions since 1964 IMP Electronics Solutions
Manufacturing / Production Technology, Hardware & Services
Over more than six decades, IMP Electronics Solutions has built a reputation for technical expertise, reliable supply chains, and strong partnerships with both customers and manufacturing partners.
Read more...Driving excellence in electronics manufacturing Jemstech
Editor's Choice Manufacturing / Production Technology, Hardware & Services
Jemstech’s reputation for disciplined execution and client-focused service has earned it strong loyalty from companies operating in demanding industries.
Read more...When do you need Nitrogen in reflow? Truth Electronic Manufacturing
Manufacturing / Production Technology, Hardware & Services
Nitrogen in reflow soldering is often seen as a performance enhancer, offering improved wetting, shinier joints, and fewer defects. But it is not always necessary.
While every effort has been made to ensure the accuracy of the information contained herein, the publisher and its agents cannot be held responsible for any errors contained, or any loss incurred as a result. Articles published do not necessarily reflect the views of the publishers. The editor reserves the right to alter or cut copy. Articles submitted are deemed to have been cleared for publication. Advertisements and company contact details are published as provided by the advertiser. Technews Publishing (Pty) Ltd cannot be held responsible for the accuracy or veracity of supplied material.
printer friendly version