Interconnection


Flexible 50 GHz and 67 GHz cable assemblies

25 November 2020 Interconnection

The W2 Series is a complete line of high-performance, flexible microwave cable assemblies from Withwave. Specially, the W205 Series has a low-density PTFE structure to achieve velocity propagation of 74% and excellent phase and amplitude stability performance. W205 cable assemblies have excellent RF performance up to 50 GHz and 67 GHz with 2,4 mm and 1,85 mm connectors, respectively.

The W205 parts have a 0,51 cm diameter centre conductor, characteristic impedance of 50 Ω, and maximum VSWR (voltage standing wave ratio) of less than 1,3. Applications include 5G Testing, telecommunication systems, environmental test chambers and test bench systems.

For more information contact Andrew Hannay, RFiber Solutions, +27 82 494 5466, sales@rfibersolutions.com, www.rfibersolutions.com


Credit(s)



Share this article:
Share via emailShare via LinkedInPrint this page

Further reading:

Hybrid device connectors with knurled nut
25 November 2020, Phoenix Contact , Interconnection
M23 Hybrid series device connectors from Phoenix Contact are now also available with a knurled nut. This enables devices such as servo drives to be connected using either coupler or cable connectors. ...

Read more...
Wideband digital RF attenuator
25 November 2020, RFiber Solutions , Telecoms, Datacoms, Wireless, IoT
The AM2010 from Atlanta Micro is a wideband, 31 dB, 5-bit digital attenuator covering the DC to 30 GHz frequency range in 1 dB steps. The positive control device provides low insertion loss, flat frequency ...

Read more...
MACOM debuts Pure Carbide power amplifiers
25 November 2020, RFiber Solutions , Telecoms, Datacoms, Wireless, IoT
MACOM Technology Solutions announced at the virtual International Microwave Symposium (IMS) the introduction of its new gallium nitride on silicon carbide (GaN-on-SiC) power amplifier product line, which ...

Read more...
Broadband bypassable amplifier
25 November 2020, RFiber Solutions , Telecoms, Datacoms, Wireless, IoT
Atlanta Micro’s AM1101 is a broadband bypassable amplifier covering the 2 GHz to 26,5 GHz frequency range. The device exhibits low noise figure and low gain across the entire frequency range while drawing ...

Read more...
Low board-to-board RF coax connectors
25 November 2020, Hiconnex , Interconnection
The IMP-LP product range is Radiall’s lowest board-to-board distance solution with optimised RF performance. This small form factor system features a pressure contact design to provide a quick and reliable ...

Read more...
5-bit digital step attenuator
25 November 2020, RFiber Solutions , Telecoms, Datacoms, Wireless, IoT
The AM2010, made by Atlanta Micro, is a wideband, 31 dB, 5-bit digital attenuator covering the DC to 30 GHz frequency range in 1 dB steps. The positive control device provides low insertion loss, flat ...

Read more...
Ultra-flexible Ku/Ka-band cable
28 October 2020, Hiconnex , Interconnection
As a leader in civil aircraft interconnection and RF cables, Radiall introduces a new cable in response to ARINC 791 and ARINC 792 requirements. This new ultra-flexible cable is ideally suited for Ku/Ka-band ...

Read more...
RF amplifier for linear and saturated applications
28 October 2020, RFiber Solutions , Telecoms, Datacoms, Wireless, IoT
The MAPC-A1103 is a high-power GaN-on-silicon-carbide HEMT D-mode amplifier suitable for DC to 2,7 GHz frequency operation. The device supports both CW and pulsed operation with peak output power levels ...

Read more...
Power and signal connectors with selective mate keying
25 November 2020, Vepac Electronics , Interconnection
The SB Smart range from Anderson Power Products is designed for applications where storage batteries intelligently interact with the system. Two primary power positions (up to 230 A each) are combined ...

Read more...
What makes good connector design?
25 November 2020, IPD Electronics , Editor's Choice, Interconnection
It’s important to remember that your connector may have physical design constraints like a minimum wire gauge or number of contacts, so it’s vital to consult with your connector supplier early in the process.

Read more...