Telecoms, Datacoms, Wireless, IoT


Cross-polarised antenna for 5G/4G

25 August 2021 Telecoms, Datacoms, Wireless, IoT

The TGX.45.A.BI.01 from Taoglas is a cross-polarised omnidirectional antenna that operates in sub-6 GHz cellular bands from 450 to 6000 MHz. It consists of two dipole antennas that are orthogonally positioned relative to each other, to efficiently receive ±45° polarised signals that are broadcast by most base stations. This also enhances its throughput capacity to provide good efficiency and gain for 5G/4G cellular communications. The cross-polarised antenna’s layout also enhances MIMO performance capabilities, thus improving signal quality.

The antenna has been developed to operate in 5G NR bands between 3300 and 4200 MHz and also covers band 31 (450 MHz) and band 71 (617 MHz) at the lower end of the 5G/4G frequency spectrum. It is available in an IP65-rated enclosure with multiple mounting options that include wall/pole or glass mounting that can be done using suction cups from Taoglas.

The TGX.45.A.BI.01 is available with a CFD-200 cable (customisable length) and an SMA male connector. It is ideal for 4x4 MIMO applications that include gateways, routers and wireless access points.

For more information contact Andrew Hutton, RF Design, +27 21 555 8400, andrew@rfdesign.co.za, www.rfdesign.co.za


Credit(s)



Share this article:
Share via emailShare via LinkedInPrint this page

Further reading:

Using Wlink cellular routers for telematics
Otto Wireless Solutions Telecoms, Datacoms, Wireless, IoT
In addition to Wi-Fi, cellular networks could be used to facilitate communication between remote vehicles and monitoring centres.

Read more...
Tibbo powers cloud-enabled traceability systems
RF Design Telecoms, Datacoms, Wireless, IoT
The wireless nature of the WS1102 allows units (and attached barcode scanners) to be moved freely between workstations.

Read more...
0,9-18 GHz miniature receiver module
RFiber Solutions Telecoms, Datacoms, Wireless, IoT
Atlanta Micro’s AM9018 is designed for low-SWaP applications and can be mounted to a host circuit board for use in multi-channel receiver applications.

Read more...
2-way power divider
RF Design Telecoms, Datacoms, Wireless, IoT
The power divider is suitable for use in test and measurement, satcom, commercial, military and wireless communication applications.

Read more...
5 GHz Wi-Fi front-end module
RF Design Telecoms, Datacoms, Wireless, IoT
A key feature of the integrated logarithmic power detector is to enable power control across the entire power spectrum.

Read more...
NFC/RFID demonstration kit
Altron Arrow Telecoms, Datacoms, Wireless, IoT
The boards are powered through their USB connectors and are supported by downloadable schematics, BOM, Gerber files, drivers and firmware sources.

Read more...
Automatic gain-controlled amplifier
RF Design Telecoms, Datacoms, Wireless, IoT
The device is designed for rugged military environments and can be customised with an optional time delay adjustment and phase modulation compression.

Read more...
2 GHz to 18 GHz bandpass filter bank
RFiber Solutions Telecoms, Datacoms, Wireless, IoT
Atlanta Micro’s new AM3215 is a 2 GHz to 18 GHz bandpass filter bank with low loss and high rejection, ideally suited for low-SWaP applications.

Read more...
High-voltage power inductors
RF Design Passive Components
Coilcraft’s RFC0807BV Series power inductors are a high-voltage version of the RFC0807B Series. Their operating voltage is rated at 800 V, which is higher than comparable products in the market. They ...

Read more...
Fixed RF attenuators
RF Design Telecoms, Datacoms, Wireless, IoT
The parts are suitable for satellite comms, instrumentation, amplifier circuits, transmit/receive modules, up/down converters, radar and broadcast applications.

Read more...