Multichannel transceiver chip for low-cost robust RF performance

Telecoms, Datacoms, Wireless, IoT

Microwave semiconductor & tube suppliers

Radio system suppliers

RF module & subsystem suppliers

Telephony IC suppliers

Wireless system IC/module suppliers

printer friendly version

5 May 2004 Telecoms, Datacoms, Wireless, IoT

Chipcon's new CC1021, a multichannel RF transceiver for relaxed narrowband operations (ie with 50 kHz or wider channel spacing), is a cost-optimised version of the CC1020, and operates in the 402-470 MHz and 804-940 MHz frequency ranges. The CC1021 offers the same unique features as the CC1020 RF transceiver, and complies with EN 300 220 and FCC CFR part 15.

As the CC1020, the CC1021 has a software configurable radio architecture, offering unique flexibility. RF frequency, modulation (GFSK/FSK/ASK/OOK), Manchester/NRZ, output power, data rate and IF bandwidth can be programmed via and SPI-compatible interface to optimise each individual application and create low-cost, but still robust, RF communication. With an image rejection mixer and a frequency-agile PLL with fine frequency resolution, the CC1021 is well suited to multichannel systems in the ISM/SRD bands at 433/868 MHz (Europe) and 915 MHz (USA).

As it requires only a few external components, the CC1021 achieves a minimal bill of material. It offers a programmable data rate of up to 153,6 Kbps, a 2,3 to 3,6 supply voltage, programmable output power up to dBm, fully on-chip VCO, programmable carrier frequency and intelligent wake-up circuitry for power management. It is supported by a development kit to aid designers.

For more information contact Kevin Jurrius, Components & System Design, 011 979 4274, [email protected]

Share this article:

SIMCom’s A7673x series
Otto Wireless Solutions Telecoms, Datacoms, Wireless, IoT
SIMCom recently released the A7673X series, a Cat.1 bis module based on the ASR1606 chipset, that supports wireless communication modes of LTE-FDD, with a maximum downlink rate of 10 Mbps and a maximum uplink rate of 5 Mbps.

Read more...

Accelerating the commercialisation of the 5G IoT markets
Altron Arrow Editor's Choice Telecoms, Datacoms, Wireless, IoT
Fibocom unveils Non-Terrestrial Networks (NTN) module MA510-GL, enabling satellite and cellular connectivity to IoT applications.

Read more...

Long-range connectivity module
Avnet Silica Telecoms, Datacoms, Wireless, IoT
Digi XBee XR 868 RF Modules support the deployment of long-range connectivity applications, and support point-to-point and mesh networking protocols.

Read more...

4G LTE-M/NB-IoT connectivity reference design
iCorp Technologies Telecoms, Datacoms, Wireless, IoT
Developed around the industry-leading Nordic nRF9160 module, the platform comes complete with a newly-developed LTE antenna, ATRIA, which is pre-certified to operate over the full LTE-M and NB-IoT bands.

Read more...

Antennas to meet all connectivity requirements
Electrocomp Telecoms, Datacoms, Wireless, IoT
Kyocera AVX RF antennas meet today’s connectivity demands in the LTE, Wi-Fi, Bluetooth, GNSS, and ISM wireless bands, available in surface mount, patch or external configurations.

Read more...

Introducing SIMCom’s new A7673X series
Otto Wireless Solutions Telecoms, Datacoms, Wireless, IoT
SIMCom recently released the A7673X series, a Cat 1 bis module that supports LTE-FDD, with a maximum downlink rate of 10 Mbps and an uplink rate of 5 Mbps.

Read more...

18 W monolithic microwave amplifier
RFiber Solutions Telecoms, Datacoms, Wireless, IoT
The CHA8612-QDB is a two stage, high-power amplifier operating between 7,9 and 11 GHz. The monolithic microwave amplifier can typically provide 18 W of saturated output power and 40% of power-added efficiency.

Read more...

Categories

Telecoms, Datacoms, Wireless, IoT

Multichannel transceiver chip for low-cost robust RF performance

Further reading:

Publications by Technews