2,4 / 5 GHz antennas

Telecoms, Datacoms, Wireless, IoT

Microwave semiconductor & tube suppliers

Radio system suppliers

RF module & subsystem suppliers

Telephony IC suppliers

Wireless system IC/module suppliers

printer friendly version

29 October 2014 Telecoms, Datacoms, Wireless, IoT

Molex’s range of 2,4 / 5 GHz standalone antennas combine ground-plane-independent design with high radiation efficiency.

Series 47950 antennas include the small footprint 34,5 by 9,00 mm version that delivers 75% minimum total efficiency in the 2,4 GHz band, with a minimum of 60% in the 5 GHz band. The hallmark of this product is its small footprint, since it fits into many wireless devices easily.

The larger 35,9 by 15,90 mm model is for applications that require the highest level of RF performance. It gives an efficiency of at least 80% in the 2,4 GHz band with 70% minimum in the 5 GHz band. These products can be used in wireless applications including Wi-Fi access points, consumer electronics, telemedicine devices and more.

An important feature of these antennas is their dipole-style design which makes them independent from the printed circuit board dimensions used in the wireless application. Since they are ground-independent, they can be applied in any device without the constraints and concerns of PCB grounding or PCB ground-induced radiation.

The antennas are applied by simply peeling off the poly-flexible adhesive tape on the underside and sticking it on any desired surface within the device casing. Once the UFL-type coaxial connector (located at the end of the micro-coaxial cable) is connected to the device radio, the antenna is ready to use.

For more information contact Craig Gibbs, Avnet Kopp, +27 (0)11 319 8600, [email protected], www.avnet.co.za

Share this article:

SIMCom’s A7673x series
Otto Wireless Solutions Telecoms, Datacoms, Wireless, IoT
SIMCom recently released the A7673X series, a Cat.1 bis module based on the ASR1606 chipset, that supports wireless communication modes of LTE-FDD, with a maximum downlink rate of 10 Mbps and a maximum uplink rate of 5 Mbps.

Read more...

Accelerating the commercialisation of the 5G IoT markets
Altron Arrow Editor's Choice Telecoms, Datacoms, Wireless, IoT
Fibocom unveils Non-Terrestrial Networks (NTN) module MA510-GL, enabling satellite and cellular connectivity to IoT applications.

Read more...

Long-range connectivity module
Avnet Silica Telecoms, Datacoms, Wireless, IoT
Digi XBee XR 868 RF Modules support the deployment of long-range connectivity applications, and support point-to-point and mesh networking protocols.

Read more...

4G LTE-M/NB-IoT connectivity reference design
iCorp Technologies Telecoms, Datacoms, Wireless, IoT
Developed around the industry-leading Nordic nRF9160 module, the platform comes complete with a newly-developed LTE antenna, ATRIA, which is pre-certified to operate over the full LTE-M and NB-IoT bands.

Read more...

Antennas to meet all connectivity requirements
Electrocomp Telecoms, Datacoms, Wireless, IoT
Kyocera AVX RF antennas meet today’s connectivity demands in the LTE, Wi-Fi, Bluetooth, GNSS, and ISM wireless bands, available in surface mount, patch or external configurations.

Read more...

Introducing SIMCom’s new A7673X series
Otto Wireless Solutions Telecoms, Datacoms, Wireless, IoT
SIMCom recently released the A7673X series, a Cat 1 bis module that supports LTE-FDD, with a maximum downlink rate of 10 Mbps and an uplink rate of 5 Mbps.

Read more...

18 W monolithic microwave amplifier
RFiber Solutions Telecoms, Datacoms, Wireless, IoT
The CHA8612-QDB is a two stage, high-power amplifier operating between 7,9 and 11 GHz. The monolithic microwave amplifier can typically provide 18 W of saturated output power and 40% of power-added efficiency.

Read more...

Categories

Telecoms, Datacoms, Wireless, IoT

2,4 / 5 GHz antennas

Further reading:

Publications by Technews