RF Design

Tel: +27 21 555 8400
Email: [email protected]
www: www.rfdesign.co.za
more information about RF Design

GNSS disciplined oscillators
9 November 2016, RF Design, Analogue, Mixed Signal, LSI

Vectron has released three new GNSS disciplined oscillators. The MD–171 is an extended holdover GNSS disciplined module, fully integrated in a compact surface-mount 40 x 50 mm footprint. The module ...
read more


Microprocessor corrected crystal oscillator
9 November 2016, RF Design, Analogue, Mixed Signal, LSI

Vectron has released a microprocessor corrected crystal oscillator (MCXO) achieving tight stabilities over the −20°C to 70°C temperature range. Measuring 9 x 7 mm, the MX–600 uses Vectron’s compensation ...
read more


High-temperature VCXO
9 November 2016, RF Design, Analogue, Mixed Signal, LSI

The VX–708 from Vectron is a high-temperature voltage control crystal oscillator (VCXO) with a 4–point resonator mount for high shock and vibration environments. With an operating temperature range ...
read more


LTE Cat. 1 plus GNSS module
9 November 2016, RF Design, Telecoms, Datacoms, Wireless, IoT

New from u-blox is the LARA-R3121, a module comprising a single-mode LTE Category 1 modem and a GNSS (global navigation satellite system) positioning engine specifically designed for IoT and M2M devices. ...
read more


Programmable sensors to teach basic wireless technology and programming skills
9 November 2016, RF Design, Telecoms, Datacoms, Wireless, IoT

Nordic Semiconductor revealed that Pune, India-based technology startup, Plezmo, has selected Nordic’s nRF52832 Bluetooth low energy system-on-chip (SoC) for its Plezmo platform of intelligent wireless ...
read more


GaN power amplifiers for radar
9 November 2016, RF Design, Telecoms, Datacoms, Wireless, IoT

Qorvo recently introduced two new power amplifiers (PAs) including the industry’s first 500 W, L-band PA internally matched to 50 Ω. These high-power devices are optimised for use in defence and civilian ...
read more


Compact GNSS antenna module
9 November 2016, RF Design, Telecoms, Datacoms, Wireless, IoT

SAM-M8Q from u-blox is a GNSS patch antenna module that is ideal for easy and reliable GNSS integration. With the performance of the u-blox M8 concurrent GNSS (GPS, GLONASS, Galileo, QZSS and SBAS) engine, ...
read more


High-power RF termination
9 November 2016, RF Design, Telecoms, Datacoms, Wireless, IoT

The PPT975-200LP from API Inmet is a low-PIM, flanged termination that operates from DC to 4 GHz. It can handle up to 200 W of power, has a resistive tolerance of 5% and a VSWR of under 1,25:1. This ...
read more


Distributed RF amplifier
9 November 2016, RF Design, Telecoms, Datacoms, Wireless, IoT

The CMD240P4 from Custom MMIC is a distributed RF amplifier that operates from DC to 22 GHz. It provides flat, stable gain of 15 dB and a 1 dB compression point of +19 dBm. The amplifier has a low noise ...
read more


BLE dev kit for wearables supports AirFuel
9 November 2016, RF Design, Telecoms, Datacoms, Wireless, IoT

Nordic Semiconductor announces that ON Semiconductor has selected its nRF52832 Bluetooth low energy system-on-chip (SoC) for its Wearable Development Kit (WDK1.0). The kit provides a complete hardware ...
read more


VCSO for harsh environments
9 November 2016, RF Design, Analogue, Mixed Signal, LSI

The VS-506 VCSO (voltage controlled saw oscillator) from Vectron is a high-frequency, ultra low phase noise and low G-sensitivity oscillator designed to support harsh environmental applications. It provides ...
read more


Mesh network built on Nordic’s Bluetooth SoC
9 November 2016, RF Design, Telecoms, Datacoms, Wireless, IoT

Nordic Semiconductor revealed that its nRF51822 Bluetooth low energy system-on-chip (SoC) has been selected by Vitir, a Norgegian wireless network solutions company, for its MergeRF system. MergeRF is ...
read more





<< First   < Previous   Page 50 of 131   Next >   Last >>







While every effort has been made to ensure the accuracy of the information contained herein, the publisher and its agents cannot be held responsible for any errors contained, or any loss incurred as a result. Articles published do not necessarily reflect the views of the publishers. The editor reserves the right to alter or cut copy. Articles submitted are deemed to have been cleared for publication. Advertisements and company contact details are published as provided by the advertiser. Technews Publishing (Pty) Ltd cannot be held responsible for the accuracy or veracity of supplied material.




© Technews Publishing (Pty) Ltd | All Rights Reserved