SLICs for new telecoms

Telecoms, Datacoms, Wireless, IoT

Microwave semiconductor & tube suppliers

Radio system suppliers

RF module & subsystem suppliers

Telephony IC suppliers

Wireless system IC/module suppliers

printer friendly version

10 September 2003 Telecoms, Datacoms, Wireless, IoT Access Control & Identity Management

Subscriber line interface circuits from Silver Telecom are ideal for all applications from network access and low-cost business telephone systems through to the latest CTI and VoIP products.

These SLICs have high density packaging formats (72 pin SIMM and SIL) and a minimum of external components are required; intelligent power-down reduces idle power consumption to <50 mW and they can drive long loops (over 10 km).

Other features are: battery reversal and on-hook transmission for CLI; programmable impedance; programmable loop current and switch hook detection threshold; meter pulse injection; soft shutdown under fault conditions.

* Quad SLICs: Ag1400 Quad SLIC - four-channel SLIC for high functionality and high density line card applications; Ag1405 Quad SLIC includes MP injection and programmable impedance; Ag1450 Quad ringing SLIC - four-channel short loop SLIC with onboard ringing generation; Ag1455 Quad ringing SLIC - four-channel short loop SLIC with onboard ringing generation and programmable impedance; Ag1415 low cost Quad SLIC - basic functionality for PABX and CTI applications.

* Dual SLICs: Ag1250 dual ringing SLIC - two-channel short loop SLIC with onboard ringing generation; Ag1255 dual ringing SLIC - two-channel short loop SLIC with onboard ringing generation and programmable impedance.

* Single SLICs: Ag1110 SLIC - single channel SLIC for low-cost applications, needing low power and long line length.

For more information contact Prime Semiconductors, 011 447 6527.

Share this article:

SIMCom’s A7673x series
Otto Wireless Solutions Telecoms, Datacoms, Wireless, IoT
SIMCom recently released the A7673X series, a Cat.1 bis module based on the ASR1606 chipset, that supports wireless communication modes of LTE-FDD, with a maximum downlink rate of 10 Mbps and a maximum uplink rate of 5 Mbps.

Read more...

Accelerating the commercialisation of the 5G IoT markets
Altron Arrow Editor's Choice Telecoms, Datacoms, Wireless, IoT
Fibocom unveils Non-Terrestrial Networks (NTN) module MA510-GL, enabling satellite and cellular connectivity to IoT applications.

Read more...

Long-range connectivity module
Avnet Silica Telecoms, Datacoms, Wireless, IoT
Digi XBee XR 868 RF Modules support the deployment of long-range connectivity applications, and support point-to-point and mesh networking protocols.

Read more...

4G LTE-M/NB-IoT connectivity reference design
iCorp Technologies Telecoms, Datacoms, Wireless, IoT
Developed around the industry-leading Nordic nRF9160 module, the platform comes complete with a newly-developed LTE antenna, ATRIA, which is pre-certified to operate over the full LTE-M and NB-IoT bands.

Read more...

Antennas to meet all connectivity requirements
Electrocomp Telecoms, Datacoms, Wireless, IoT
Kyocera AVX RF antennas meet today’s connectivity demands in the LTE, Wi-Fi, Bluetooth, GNSS, and ISM wireless bands, available in surface mount, patch or external configurations.

Read more...

Introducing SIMCom’s new A7673X series
Otto Wireless Solutions Telecoms, Datacoms, Wireless, IoT
SIMCom recently released the A7673X series, a Cat 1 bis module that supports LTE-FDD, with a maximum downlink rate of 10 Mbps and an uplink rate of 5 Mbps.

Read more...

18 W monolithic microwave amplifier
RFiber Solutions Telecoms, Datacoms, Wireless, IoT
The CHA8612-QDB is a two stage, high-power amplifier operating between 7,9 and 11 GHz. The monolithic microwave amplifier can typically provide 18 W of saturated output power and 40% of power-added efficiency.

Read more...

Categories

Telecoms, Datacoms, Wireless, IoT

SLICs for new telecoms

Further reading:

Publications by Technews