Due to the high number of cellular engine-based applications developed over the last couple of years, a need has arisen for RF splitters that can accommodate more than two or four antennas. Poynting Antennas therefore developed an 8-way splitter for GSM bands.
Most cellular engine-based applications combine a number of such units. Most notably where least cost routers (LCR) are installed for companies with high traffic patterns. These routers are then stacked and often located in the basement of the building. This causes bad performance as reception and propagation in the PABX location is often bad and the individual antennas interfere and couple with each other.
The 8-way splitter can combine eight GSM modules and furthermore can then be used with a single antenna which can be mounted outdoors. The Poynting 800-2000 MHz 7 dBi Log Periodic is ideal for this purpose. Where more than eight low cost routers are co-located, the installer can furthermore point the outdoor directional antennas to different base stations to spread the GSM traffic and reduce the possibility of overloading a single base station.
Full sensor to cloud solution CST Electronics
Telecoms, Datacoms, Wireless, IoT
NeoCortec has demonstrated the seamless and rapid development of full sensor-to-cloud solutions using NeoMesh Click boards from MikroE and the IoTConnect cloud solution from Avnet.
Read more...Long-range Wi-Fi HaLow module TRX Electronics
Telecoms, Datacoms, Wireless, IoT
One of Mouser’s newest products is the Morse Micro MM6108-MF08651-US Wi-Fi HaLow Module, which adheres to the IEEE 802.11ah standard.
Read more...Quectel launches 3GPP NTN comms module Quectel Wireless Solutions
Telecoms, Datacoms, Wireless, IoT
Quectel Wireless Solutions has announced the Quectel BG95-S5 3GPP non-terrestrial network (NTN) satellite communication module.
Read more...SIMCom’s A7673x series Otto Wireless Solutions
Telecoms, Datacoms, Wireless, IoT
SIMCom recently released the A7673X series, a Cat.1 bis module based on the ASR1606 chipset, that supports wireless communication modes of LTE-FDD, with a maximum downlink rate of 10 Mbps and a maximum uplink rate of 5 Mbps.
Read more...Long-range connectivity module Avnet Silica
Telecoms, Datacoms, Wireless, IoT
Digi XBee XR 868 RF Modules support the deployment of long-range connectivity applications, and support point-to-point and mesh networking protocols.
Read more...4G LTE-M/NB-IoT connectivity reference design iCorp Technologies
Telecoms, Datacoms, Wireless, IoT
Developed around the industry-leading Nordic nRF9160 module, the platform comes complete with a newly-developed LTE antenna, ATRIA, which is pre-certified to operate over the full LTE-M and NB-IoT bands.
Read more...Antennas to meet all connectivity requirements Electrocomp
Telecoms, Datacoms, Wireless, IoT
Kyocera AVX RF antennas meet today’s connectivity demands in the LTE, Wi-Fi, Bluetooth, GNSS, and ISM wireless bands, available in surface mount, patch or external configurations.
Read more...Introducing SIMCom’s new A7673X series Otto Wireless Solutions
Telecoms, Datacoms, Wireless, IoT
SIMCom recently released the A7673X series, a Cat 1 bis module that supports LTE-FDD, with a maximum downlink rate of 10 Mbps and an uplink rate of 5 Mbps.
Read more...18 W monolithic microwave amplifier RFiber Solutions
Telecoms, Datacoms, Wireless, IoT
The CHA8612-QDB is a two stage, high-power amplifier operating between 7,9 and 11 GHz. The monolithic microwave amplifier can typically provide 18 W of saturated output power and 40% of power-added efficiency.
printer friendly version