CST Electronics

Tel: +27 11 608 0070
Email: natasha@cstelectronics.co.za
www: www.cstelectronics.co.za
more information about CST Electronics

Analog temperature sensor accurate to ±0,5°C
2 June 2004, Analogue, Mixed Signal, LSI

Dallas Semiconductor's temperature sensor chip, the DS600, is a ±0,5°C (max) accurate analog-output temperature sensor. The device comes factory calibrated and has a linear-voltage output characteristic, ...
read more


300-450 MHz superheterodyne ASK/FSK receiver
2 June 2004, Telecoms, Datacoms, Wireless, IoT

Claimed to be the world's first dual-channel receiver that can receive both ASK and FSK data simultaneously, eliminating the switching lag time between modes, the MAX1471 from Maxim is designed for low-cost ...
read more


Designing robust and fault-tolerant motion-control feedback systems
19 May 2004, Analogue, Mixed Signal, LSI, Test & Measurement

Ref: z2708354m Today's demanding industrial applications require rugged, reliable robots and automated machines that operate under harsh conditions 24 hours a day, seven days a week. Such systems require ...
read more


Power meter design achieves ±1% accuracy
5 May 2004, Analogue, Mixed Signal, LSI

Power meters provide an early warning of thermal overload by monitoring the power consumption in 'high reliability' systems. Power monitoring is especially suitable for systems in which the ...
read more


Low-power multirate limiting amplifiers
5 May 2004, Analogue, Mixed Signal, LSI

Maxim's MAX3747/MAX3747A are 3,3 V, low-power, multirate limiting amplifiers with a programmable loss-of-signal (LOS) indicator. These devices provide high gain and good bit-error-rate performance with ...
read more


PWM power IC integrates MOSFETs and hot-swap controller
21 April 2004, Power Electronics / Power Management

Maxim's MAX5042 is a two-switch, clamped, PWM converter with integrated hot-swap controller. This is a unique device that the company says simplifies the design of small, high-performance, isolated power ...
read more


Filterless 15 W class-D audio amplifier
21 April 2004, Analogue, Mixed Signal, LSI

Maxim claims its 15 W, mono, filterless, Class-D audio amplifier, the MAX9703, offers the audio quality typically associated with linear (Class-AB) amps and the benefits of high-efficiency Class-D operation, ...
read more


Trends in cooling high-speed chips - automatic fan control
7 April 2004, Power Electronics / Power Management

Cooling fans are an important part of thermal management for high-powered chips and systems. Unfortunately, their use can sometimes raise a system's acoustic noise level to the point where it is objectionable. ...
read more


Submicro op-amps with internal voltage reference operate down to 1,4 V
7 April 2004, Analogue, Mixed Signal, LSI

Maxim has introduced the MAX4036-MAX4039, claimed to be the industry's smallest submicro op-amps with and without an integrated reference voltage. The MAX4037 (single) and MAX4039 (dual) feature a 1,232 ...
read more


High linearity RF driver amplifier released
7 April 2004, Telecoms, Datacoms, Wireless, IoT

EiC Corporation, the company that pioneered InGaP/GaAs MMIC amplifiers, has released a new RF MMIC power amplifier for the 3 G and base station market. The ECG099B has high linearity - typically 41 dBm ...
read more


Profile on CST Electronics
7 April 2004, News

CST Electronics originated from Tarsus Electronic Components that was formed in 1991 and which established the Dallas Semiconductor and iButton line in the South African market. In 1997 CST Tarsus was ...
read more


RFICs for Wireless Communication Products
7 April 2004, Technical Literature, Telecoms, Datacoms, Wireless, IoT

Product selection guide details EiC's uniquely-developed InGaP/GaAs HBT process devices for RF communications that are exceptionally reliable. Line-up specifies: gain block amplifiers (Darlington config); ...
read more





<< First   < Previous   Page 46 of 52   Next >   Last >>







While every effort has been made to ensure the accuracy of the information contained herein, the publisher and its agents cannot be held responsible for any errors contained, or any loss incurred as a result. Articles published do not necessarily reflect the views of the publishers. The editor reserves the right to alter or cut copy. Articles submitted are deemed to have been cleared for publication. Advertisements and company contact details are published as provided by the advertiser. Technews Publishing (Pty) Ltd cannot be held responsible for the accuracy or veracity of supplied material.




© Technews Publishing (Pty) Ltd | All Rights Reserved